MAX4477AUA+T
| Parameters | |
|---|---|
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifiers |
| Packing Method | TAPE AND REEL |
| Max Power Dissipation | 362mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4477 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Power Supplies | 3/5V |
| Number of Circuits | 2 |
| Operating Supply Current | 2.5mA |
| Nominal Supply Current | 2.2mA |
| Output Current | 48mA |
| Slew Rate | 3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 90 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V ±1.35V~2.75V |
| Output Current per Channel | 48mA |
| Input Offset Voltage (Vos) | 70μV |
| Bandwidth | 10MHz |
| Unity Gain BW-Nom | 10000 kHz |
| Voltage Gain | 120dB |
| Average Bias Current-Max (IIB) | 0.00015μA |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00015μA |
| Programmable Power | NO |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
MAX4477AUA+T Overview
In order to protect the op amps, a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case is used. An op amp ic of the General Purpose type. As far as the packaging is concerned, buffer op amp is delivered in a Tape & Reel (TR) case. The number of terminations is approaching the 8 mark. Linear amplifier has a total of 8 pins. Please take in mind that op amp should be run at 5V. A type of Operational Amplifiers op amp ic can be identified by the fact that this is a type of Operational Amplifiers device. The buffer op amp includes 8 pins. With regards to the offset voltage of the input, buffer amplifier is rated at 70μV. Surface Mount is the recommended mounting type of operational amplifiers. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~125°C for optimal performance. Using an 2.5mA supply current, this operational amplifier ics can be operated. You should keep the voltage gain at 120dB for the time being. On this buffer amplifier, there are 2 circuits. On the output type, there are Rail-to-Rail different types of op amps. For the packing of the instrumentation amplifier, TAPE AND REEL is adopted.
MAX4477AUA+T Features
8 Pins
supply voltage of 5V
120dB voltage gain
Output Type: Rail-to-Rail
MAX4477AUA+T Applications
There are a lot of Maxim Integrated MAX4477AUA+T Instrumentational OP Amps applications.
- Oscilloscopes
- E-book readers
- Ultrasound transducers
- Inverse/same-phase proportional circuit
- High-frequency data acquisition systems
- Video computer boards
- Subtraction operation circuits
- Division circuits
- Industrial control system
- Test equipment
