MAX4478ASD
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2012 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Max Power Dissipation | 667mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4478 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Power Supplies | 3/5V |
| Number of Channels | 4 |
| Operating Supply Current | 2.5mA |
| Nominal Supply Current | 2.2mA |
| Output Current | 48mA |
| Slew Rate | 3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 90 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V ±1.35V~2.75V |
| Output Current per Channel | 48mA |
| Input Offset Voltage (Vos) | 70μV |
| Bandwidth | 10MHz |
| Unity Gain BW-Nom | 10000 kHz |
| Voltage Gain | 120dB |
| Average Bias Current-Max (IIB) | 0.00015μA |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00015μA |
| Programmable Power | NO |
| Height | 1.5mm |
| Length | 8.75mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX4478ASD Overview
In the package, you will find a 14-SOIC (0.154, 3.90mm Width)-case to contain the op amp ic. The instrumentation amplifier in this picture is of the General Purpose-type. As far as the packaging is concerned, buffer op amp is delivered in a Tube case. During the past two weeks, there have been close to 14 terminations. The pins on this board total to 14 in total. It is important to remember that this op amp should be operated at a voltage of 5V volts. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifier devices. The buffer op amp includes 14 pins. Regarding input offset voltage, op amp rates 70μV. For this electronic part, it is recommended that you mount it with type Surface Mount. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~125°C . It is possible to operate this buffer amplifier from a supply current of 2.5mA . It is recommended to keep the voltage gain at 120dB at all times. There are 4 channels on the operational amplifiers. One of the many advantages that this linear amplifier has, among many other things, is the fact that it outputs Rail-to-Rail signals.
MAX4478ASD Features
14 Pins
supply voltage of 5V
120dB voltage gain
Output Type: Rail-to-Rail
MAX4478ASD Applications
There are a lot of Maxim Integrated MAX4478ASD Instrumentational OP Amps applications.
- Integrator circuits
- Blood pressure sensors
- Portable electronic products powered by batteries
- High/low-pass filter circuit
- Video data acquisition
- Subtraction operation circuits
- High speed sample
- Commercial audio systems
- Video amplifiers
- High-frequency data acquisition systems
