MAX4488AUT+T
| Parameters | |
|---|---|
| Bandwidth | 42MHz |
| Unity Gain BW-Nom | 42000 kHz |
| Low-Offset | YES |
| Frequency Compensation | YES AVCL>=5 |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 70μV |
| Current - Output / Channel | 48mA |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Power | NO |
| Length | 2.9mm |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Surface Mount | YES |
| Number of Pins | 6 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.95mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4488 |
| Pin Count | 6 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Power Supplies | 3/5V |
| Number of Circuits | 1 |
| Current - Supply | 2.5mA |
| Slew Rate | 10V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 115 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V ±1.35V~2.75V |
MAX4488AUT+T Overview
Op amp is packaged in SOT-23-6 case. General Purpose-type instrumentation amplifiers are used in this application. The op amp is delivered to you in a Tape & Reel (TR) case. The number of terminations is approaching the 6 mark. A total of 6 pins are located on this board. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 3V. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. In total, the buffer amplifier consists of 6 pins. This electronic part is best mounted with type Surface Mount. The buffer amplifier functions well at -40°C~125°C as far as operating temperature is concerned. This op amp ic has 1 circuits. One of the many benefits of this op amp ic is that it emits Rail-to-Rail signals. The instrumentation amplifier is packed in the form of TAPE AND REEL. It is recommended that this electronic component be used with an 2.5mA supply.
MAX4488AUT+T Features
6 Pins
supply voltage of 3V
Output Type: Rail-to-Rail
MAX4488AUT+T Applications
There are a lot of Maxim Integrated MAX4488AUT+T Instrumentational OP Amps applications.
- Weighing systems
- Biopotential
- Polarized electrodes
- Broadcasting
- ECG equipment
- Proportional operation circuits
- Tablets
- Semiconductor detectors
- Strain gauges
- Signal filtering
