MAX4490AUK+T
| Parameters | |
|---|---|
| Published | 2002 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4490 |
| Pin Count | 5 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Circuits | 1 |
| Current - Supply | 800μA |
| Slew Rate | 10V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 50pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V ±1.35V~2.75V |
| Bandwidth | 10MHz |
| Unity Gain BW-Nom | 10000 kHz |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 1.5mV |
| Current - Output / Channel | 50mA |
| Low-Bias | NO |
| Micropower | NO |
| Power | NO |
| Length | 2.9mm |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
MAX4490AUK+T Overview
The linear amplifier is packaged in a SC-74A, SOT-753 case. An op amp of this type is a General Purpose-type. Upon delivery, op amp ic is packaged in a Tape & Reel (TR) case. It is estimated that there will be 5 terminations in the next few months. The pins on this board total to 5 in total. Please take in mind that this instrumentation amplifier should be run at 5V. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifier devices. 5 pins are located on the operational amplifiers. This electronic part is recommended for mounting type Surface Mount. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of -40°C~125°C. There are 1 circuits on this op amp. On the output type, there are Rail-to-Rail different types of op amps. For the packing of the instrumentation amplifier, TAPE AND REEL is adopted. A supply of 800μA or higher is recommended for use with this electronic part.
MAX4490AUK+T Features
5 Pins
supply voltage of 5V
Output Type: Rail-to-Rail
MAX4490AUK+T Applications
There are a lot of Maxim Integrated MAX4490AUK+T Instrumentational OP Amps applications.
- Laptop
- Weighing systems
- Medical imaging
- Displayers for aircraft and air transportation control systems
- E-book readers
- Fast A/D and D/A converters
- Test and measurement instruments
- Band-stop filter
- Fission chambers
- Signal amplification
