MAX4490AXK-T
| Parameters | |
|---|---|
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Number of Pins | 70 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2000 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Max Power Dissipation | 200mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4490 |
| Pin Count | 5 |
| JESD-30 Code | R-PDSO-G5 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 2.75V |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Operating Supply Current | 800μA |
| Nominal Supply Current | 800μA |
| Output Current | 50mA |
| Slew Rate | 10V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 54 dB |
| Current - Input Bias | 50pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V ±1.35V~2.75V |
| Output Current per Channel | 50mA |
| Input Offset Voltage (Vos) | 1.5mV |
| Bandwidth | 10MHz |
| Unity Gain BW-Nom | 10000 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.0025μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Low-Bias | NO |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.0025μA |
| Length | 2mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4490AXK-T Overview
Packaged in a 5-TSSOP, SC-70-5, SOT-353 case, the buffer op amp is ready to use. An op amp ic of the General Purpose type. Linear amplifier is delivered in a Tape & Reel (TR) case. The number of terminations approaches 5. The pins on this board total to 5 in total. The linear amplifier should be run at 5V at all times, so please keep that in mind when using it. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. 70 pins are located on the operational amplifiers. With regards to the offset voltage of the input, buffer amplifier is rated at 1.5mV. This electronic part is recommended for mounting type Surface Mount. The buffer amplifier functions well at -40°C~125°C as far as operating temperature is concerned. Using a supply current of 800μA , this buffer op amp will be able to operate. Op amp is a member of the 110dB's 110dB family. There are 1 channels on the operational amplifiers. Buffer amplifier produces Rail-to-Rail signals, which is one of its many benefits. The operating supply voltage of the buffer op amp is rated at 2.75V. TAPE AND REEL is adopted to pack the instrumentation amplifier.
MAX4490AXK-T Features
5 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
MAX4490AXK-T Applications
There are a lot of Maxim Integrated MAX4490AXK-T Instrumentational OP Amps applications.
- Image computer boards
- Voltage regulation circuit
- Professional videography
- Tablets
- Test and measurement instruments
- Information processing
- Test equipment
- Logarithmic operation circuits
- Portable docking station
- Comparator
