MAX4490AXK+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2002 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4490 |
| Pin Count | 5 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Circuits | 1 |
| Current - Supply | 800μA |
| Slew Rate | 10V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 50pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V ±1.35V~2.75V |
| Bandwidth | 10MHz |
| Unity Gain BW-Nom | 10000 kHz |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 1.5mV |
| Current - Output / Channel | 50mA |
| Low-Bias | NO |
| Micropower | NO |
| Power | NO |
| Length | 2mm |
| RoHS Status | ROHS3 Compliant |
MAX4490AXK+T Overview
In order to protect the op amps, a 5-TSSOP, SC-70-5, SOT-353 case is used. Op amps are General Purpose types of amplifier on the chip. As far as the packaging is concerned, buffer op amp is delivered in a Tape & Reel (TR) case. The number of terminations approaches 5. A total of 5 pins are located on this board. Please take in mind that op amp should be run at 5V. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifier devices. The buffer op amp includes 5 pins. This electronic part is recommended for mounting type Surface Mount. With regard to operating temperature, op amp ranges -40°C~125°C. The buffer amp consists of 1 circuits in total. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. TAPE AND REEL is adopted to pack the instrumentation amplifier. There is a recommendation that this electrical part be used with a supply with 800μA current rating.
MAX4490AXK+T Features
5 Pins
supply voltage of 5V
Output Type: Rail-to-Rail
MAX4490AXK+T Applications
There are a lot of Maxim Integrated MAX4490AXK+T Instrumentational OP Amps applications.
- Signal operation
- Logarithmic operation circuits
- Inverse/same-phase proportional circuit
- Test and measurement instruments
- Multimedia playback equipment
- Differentiator circuits
- Precision measurement
- MP3
- E-book readers
- Strain gauges
