MAX4501ESA
| Parameters | |
|---|---|
| Pin Count | 8 |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 75 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 50 ns |
| On-State Resistance (Max) | 250Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 100 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 3pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 75ns, 50ns |
| Charge Injection | 1pC |
| Voltage - Supply, Single (V+) | 2V~12V |
| Normal Position | NO |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 250Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4501 |
MAX4501ESA Overview
Presented in 8-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. A high level of reliability can be achieved through the use of an advanced packaging method Tube. This analog switch is mounted in Surface Mount. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operational temperature extended around -40°C~85°C TA. Total terminations are 8. A high-quality output is provided by the electrical component's 1 channels. Powered by a 5V voltage supply, the electrical part should be switched on and run. There is an electrical component included in the 8 series. These analog multiplexers are built based on SPST - NO switching circuits. The multiplexer consists of 1 circuits. If you are looking for variants of the digital switch, trying search with MAX4501. Internally, this switch multiplexer has a resistance of 250Ohm. To find out what the 8 pins do, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. Multiplexers should not be powered above 12V in normal situations. Analog switch ics with Single supply type are cost-effective. 2V is the lowest voltage the electrical component should receive. For this multiplexer to operate, 1μA current would be sufficient. This analogue multiplexer requires a voltage of 2V~12V when it drains from a single voltage supply. A digital multiplexer may suffer damage if voltage is applied above 1μA.
MAX4501ESA Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
MAX4501ESA Applications
There are a lot of Maxim Integrated MAX4501ESA Analog Switches & Multiplexers ICs applications.
- Communication systems
- Modems
- Digital access cross connects
- Imaging
- Avionics test equipment
- Switching Systems
- Fiber In The Loop (FITL)
- Communications systems
- Automotive applications
- Optical Applications
