MAX4501EXK-T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Resistance | 250Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 200mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4501 |
| Pin Count | 5 |
| Operating Supply Voltage | 9V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 300 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 125 ns |
| On-State Resistance (Max) | 250Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 100 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 3pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 75ns, 50ns |
| Charge Injection | 1pC |
| Voltage - Supply, Single (V+) | 2V~12V |
| Normal Position | NO |
| Length | 2mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4501EXK-T Overview
Shipping overseas is convenient due to the electrical component's packing in 5-TSSOP, SC-70-5, SOT-353. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. 1:1 is the number of circuits in the multiplexer and demultiplexer. The operating temperature is extended to around -40°C~85°C TA. Total terminations are 5. This electronic part offers high-quality output due to its 1 channels. When a voltage supply of 5V is used, the electronic component should be turned on and run. The electrical component body receives 5 pins. These analog multiplexers are built based on SPST - NO switching circuits. The multiplexer consists of 1 circuits. Try searching with MAX4501 if you're looking for variants. In this multiplexer, the internal resistance is 250Ohm. To find out what the 5 pins do, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 12V volts for the multiplexer. A analog switch ic that has a cost-effective Single supply type. 2V is the lowest voltage the electrical component should receive. For this multiplexer to operate, 1μA current would be sufficient. This analog switch requires a voltage of 2V~12V to drain from a single voltage supply. Putting voltage greater than 1μA on the multiplexer may cause damage. Operating voltages of 9V are compatible with the electrical part.
MAX4501EXK-T Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
MAX4501EXK-T Applications
There are a lot of Maxim Integrated MAX4501EXK-T Analog Switches & Multiplexers ICs applications.
- Cell phones
- High speed data transmission line cards
- DSLAMs
- Routers
- Microprocessor Controlled Analog Systems
- Automotive applications
- CSU
- Fiber In The Loop (FITL)
- PCMCIA cards
- PBX interfaces
