MAX4502CPA
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 250Ohm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4502 |
| Pin Count | 8 |
| JESD-30 Code | R-PDIP-T8 |
| Qualification Status | Not Qualified |
| Supply Voltage-Max (Vsup) | 5.5V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Operating Supply Current | 1μA |
| Throw Configuration | SPST |
| Supply Type | Single |
| On-State Resistance (Max) | 250Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 100 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 3pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 75ns, 50ns |
| Charge Injection | 1pC |
| Switch-on Time-Max | 75ns |
| Switch-off Time-Max | 50ns |
| Voltage - Supply, Single (V+) | 2V~12V |
| Normal Position | NC |
| Height Seated (Max) | 4.572mm |
| Length | 9.375mm |
| Width | 7.62mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4502CPA Overview
Packed in 8-DIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. A high level of reliability can be achieved through the use of an advanced packaging method Tube. There is an analog multiplexer mounted in position Through Hole. 1:1 is the ratio between multiplexers and demultiplexers. Operation at a temperature around 0°C~70°C TA. 8 terminations have been made so far. High-quality output is provided by the electronic component's 1 channels. Turning on and running the electrical part should be easy with a 5V voltage supply. An electrical component like this is included in the 8 series. These analog multiplexers are built based on SPST - NC switching circuits. A 1 circuit is present in this switch device. Try searching with MAX4502 to find analog multiplexer variants. In this multiplexer, the internal resistance is 250Ohm. This switch device is a typical Multiplexer or Switches. Analogue multiplexers of the Single supply type that are cost-effective. It would be sufficient to run this analogue multiplexer with 1μA current. An analogue multiplexer drains from a single voltage supply at 2V~12V.
MAX4502CPA Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
MAX4502CPA Applications
There are a lot of Maxim Integrated MAX4502CPA Analog Switches & Multiplexers ICs applications.
- Communications systems
- Ultrasound
- Cable Modem
- 65 V DACs
- Microprocessor controlled systems
- Sample-and-hold systems
- HDTV
- Precision data acquisition
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- DSUs
