MAX4502CUK-T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Resistance | 900mOhm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 571mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4502 |
| Pin Count | 5 |
| Operating Supply Voltage | 9V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 300 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 125 ns |
| On-State Resistance (Max) | 250Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 100 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 3pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 75ns, 50ns |
| Charge Injection | 1pC |
| Voltage - Supply, Single (V+) | 2V~12V |
| Normal Position | NC |
| Length | 2.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX4502CUK-T Overview
The electronic component is convenient to ship overseas because it is packed in a SC-74A, SOT-753. The advanced packaging method Tape & Reel (TR) provides high reliability. Multiplexers like this are mounted in the Surface Mount position. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Extended operating temperature around 0°C~70°C TA. There are 5 terminations totally. The electronic part delivers high-quality output through its 1 channels. It is safe to turn on and run the electronic component with a 5V voltage supply. Into the electrical component body are injected 5 pins. These analog multiplexers are built based on SPST - NC switching circuits. A total of 1 circuits make up this switch device. Look for analog switch ic variants by searching with MAX4502. An switch multiplexer with 900mOhm internal resistance has a value of 900mOhm. Datasheets for 5 pin functions are available upon request. The analogue multiplexer in this example is a typical Multiplexer or Switches. A voltage higher than 12V should not normally be supplied to the switches. The digital multiplexer has a low cost Single supply. There should be 2V voltage fed to the electrical part below 2V. An operating current of 1μA would be sufficient for this switch device. This analogue multiplexer requires a voltage of 2V~12V when it drains from a single voltage supply. A digital multiplexer may suffer damage if voltage is applied above 1μA. 9V operating voltages can be used with this electrical part.
MAX4502CUK-T Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
MAX4502CUK-T Applications
There are a lot of Maxim Integrated MAX4502CUK-T Analog Switches & Multiplexers ICs applications.
- Switching Systems
- SDH/SONET multiplexers
- Cellular phones
- High speed data transmission line cards
- Cable PC
- Audio and video switching
- PCMCIA cards
- Cell phones
- PDAs
- Residential Gateways, Home Gateway/Router
