MAX4502EUK-T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Resistance | 250Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 571mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4502 |
| Pin Count | 5 |
| Operating Supply Voltage | 9V |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 300 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 125 ns |
| On-State Resistance (Max) | 250Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 100 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 3pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 75ns, 50ns |
| Charge Injection | 1pC |
| Voltage - Supply, Single (V+) | 2V~12V |
| Normal Position | NC |
| Length | 2.9mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4502EUK-T Overview
The electrical component comes in SC-74A, SOT-753 packaging, which makes it convenient to ship overseas. High reliability is provided by advanced packaging method Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. Multiplexer and demultiplexer circuits have a number 1:1. Operating temperature around -40°C~85°C TA extended. The total number of terminations is 5. A high-quality output is provided by the electrical component's 1 channels. If the voltage supply is 5V volts, the electrical component should be turned on and run. An electrical component like this is included in the 5 series. SPST - NC switching circuits are used in these analog switch ics. Search with MAX4502 if you are looking for analog multiplexer variants. There is 250Ohm internal resistance in this digital multiplexer. Datasheets for functions of 5 pins are available. A analogue multiplexer of this type is a Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 12V. Analogue multiplexer with a Single supply type that is cost-effective. The lowest voltage fed to the electronic component should be 2V. An operating current of 1μA would be sufficient for this switch device. This analogue multiplexer requires a voltage of 2V~12V when it drains from a single voltage supply. Putting voltage greater than 1μA on the multiplexer may cause damage. It can operate from 9V operating voltages.
MAX4502EUK-T Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
MAX4502EUK-T Applications
There are a lot of Maxim Integrated MAX4502EUK-T Analog Switches & Multiplexers ICs applications.
- Relay replacements
- Video signal routing
- Fault Tolerant Systems
- Fiber to the Home
- Cable Modem
- Data Acquisition Systems
- Precision data acquisition
- Industrial control systems
- Automatic test equipment
- Industrial
