MAX4503CSA
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 250Ohm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4503 |
| Pin Count | 8 |
| JESD-30 Code | R-PDSO-G8 |
| Power Supplies | +-3/+-5V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Operating Supply Current | 40μA |
| Number of Bits | 2 |
| Throw Configuration | SPST |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 250Ohm |
| Min Dual Supply Voltage | 1V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 3pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 1pC |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±1V~6V |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4503CSA Overview
As the electronic part is packed in 8-SOIC (0.154, 3.90mm Width), international shipping is convenient. The advanced packaging method Tube provides high reliability. Multiplexers like this are mounted in the Surface Mount position. 1:1 is the ratio between multiplexers and demultiplexers. Operating temperature extended to 0°C~70°C TA. Total terminations are 8. By its 1 channels, the electronic component provides high-quality output. A 5V voltage supply should turn on and run the electronic component. A total of 8 pins are injected into the electrical part body. Circuits based on SPST - NO switching are used to construct these analog switch ics. There are 1 circuits in this switch device. Try searching with MAX4503 to find analog multiplexer variants. Analog switches have 250Ohm internal resistance. In this analog multiplexer, the value is Multiplexer or Switches. An effective Dual supply digital multiplexer. For this multiplexer to operate, 40μA current would be sufficient. If put voltage greater than 6V on the multiplexer, damage may be caused to the device. For dual power supplies, a voltage of at least 1V should be attached. It can conduct in a 2-bit manner.
MAX4503CSA Features
1 Channels
Switch Circuit: SPST - NO
40μA Supply Current
2-Bit
MAX4503CSA Applications
There are a lot of Maxim Integrated MAX4503CSA Analog Switches & Multiplexers ICs applications.
- Ultrasound
- Industrial
- Battery-powered systems
- Sample-and-hold systems
- Video signal routing
- RGB switches
- SDH
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Communication systems
- Video switching
