MAX4503CUK-T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Resistance | 250Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 571mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4503 |
| Pin Count | 5 |
| Operating Supply Voltage | 6V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Operating Supply Current | 40μA |
| Nominal Supply Current | 200μA |
| Max Supply Current | 125μA |
| Number of Bits | 2 |
| Throw Configuration | SPST |
| Turn On Delay Time | 100 ns |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 250Ohm |
| Min Dual Supply Voltage | 1V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 3pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 1pC |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±1V~6V |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4503CUK-T Overview
The electrical component comes in SC-74A, SOT-753 packaging, which makes it convenient to ship overseas. This packaging method provides high reliability because it uses advanced packaging techniques. A switch device like this is mounted in Surface Mount. Multiplexer and demultiplexer circuits have a number 1:1. Operation at a temperature around 0°C~70°C TA. Totally, there are 5 terminations. By its 1 channels, the electronic component provides high-quality output. A 5V voltage supply should turn on and run the electronic component. Electronic part bodies are injected with 5 pins. A SPST - NO switching circuit is used for these analog switches. The circuits in this analogue multiplexer number 1. If you are looking for variants of the digital switch, trying search with MAX4503. The internal resistance of this digital multiplexer is 250Ohm. To find out what the 5 pins do, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. Dual supply type digital switch with a low cost. This digital switch can be operated with a current of 40μA. A voltage higher than 125μA may cause damage to the switch multiplexer. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 6V. With dual power supplies, you should attach at least 1V. 6V operating voltages are supported by the electronic component. It is capable of carrying out 2-bit operation.
MAX4503CUK-T Features
1 Channels
Switch Circuit: SPST - NO
40μA Supply Current
2-Bit
MAX4503CUK-T Applications
There are a lot of Maxim Integrated MAX4503CUK-T Analog Switches & Multiplexers ICs applications.
- ATM
- Channel Banks
- Transmit
- RGB switches
- High speed data transmission line cards
- FTTH
- Microwave transmission systems
- Video signal routing
- HDTV
- Digital access cross connects
