MAX4503ESA
| Parameters | |
|---|---|
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±1V~6V |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 250Ohm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4503 |
| Pin Count | 8 |
| JESD-30 Code | R-PDSO-G8 |
| Power Supplies | +-3/+-5V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Operating Supply Current | 40μA |
| Number of Bits | 2 |
| Throw Configuration | SPST |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 250Ohm |
| Min Dual Supply Voltage | 1V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 3pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 1pC |
MAX4503ESA Overview
The electronic component is convenient to ship overseas because it is packed in a 8-SOIC (0.154, 3.90mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. Surface Mount is where this multiplexer is located. 1:1 is the number of circuits in the multiplexer and demultiplexer. Temperatures around -40°C~85°C TA are extended for operation. In total, 8 terminations have occurred. As a result of its 1 channels, this electronic component provides high-quality output. Powered by a 5V voltage supply, the electrical part should be switched on and run. The electronic part body is injected with 8 pins. Circuits based on SPST - NO switching are used to construct these analog switch ics. The circuits in this analogue multiplexer number 1. Try searching with MAX4503 to find analog multiplexer variants. The internal resistance of this digital multiplexer is 250Ohm. It is a typical Multiplexer or Switches analog multiplexer. Analogue multiplexers of the Dual supply type that are cost-effective. For this multiplexer to operate, 40μA current would be sufficient. For this switch, a dual supply voltage is feasible, but it must not exceed 6VIt is recommended that you attach at least 1V to your dual power supply. It can conduct 2-bit signals.
MAX4503ESA Features
1 Channels
Switch Circuit: SPST - NO
40μA Supply Current
2-Bit
MAX4503ESA Applications
There are a lot of Maxim Integrated MAX4503ESA Analog Switches & Multiplexers ICs applications.
- Communication systems
- Remote Powered Equipment
- Avionics test equipment
- Fiber In The Loop (FITL)
- Video signal routing
- Avionics and Military Systems
- Residential Gateways, Home Gateway/Router
- Channel Banks
- T1/E1 Terminals
- 65 V DACs
