MAX4504CSA
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 250Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4504 |
| Pin Count | 8 |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 40μA |
| Max Supply Current | 125μA |
| Number of Bits | 2 |
| Throw Configuration | SPST |
| Turn On Delay Time | 150 ns |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 250Ohm |
| Min Dual Supply Voltage | 1V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 3pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 1pC |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Voltage - Supply, Dual (V±) | ±1V~6V |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4504CSA Overview
The electrical component comes in 8-SOIC (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. In order to provide high reliability, an advanced packaging method Tube is used. In Surface Mount, you'll find this switch device. 1:1 is the ratio between multiplexers and demultiplexers. Operating temperature extended to 0°C~70°C TA. 8 terminations have been made so far. The electronic part provides high-quality output because it has 1 channels. When the electronic component is given a voltage of 5V, it should be turned on and run. The electrical component body receives 8 pins. These analog multiplexers are built based on SPST - NC switching circuits. This multiplexer is composed of 1 circuits. Search with MAX4504 if you are looking for analog multiplexer variants. A 250Ohm internal resistance characterizes this multiplexer. Datasheets for 8 pin functions are available upon request. It is a typical Multiplexer or Switches analog multiplexer. Multiplexers should not be powered above 5.5V in normal situations. The digital multiplexer has a low cost Dual supply. The lowest voltage fed to the electronic component should be 4.5V. 1μA current would be enough for this multiplexer to operate. Putting voltage greater than 125μA on the multiplexer may cause damage. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 6V. It is recommended that you attach at least 1V to your dual power supply. A voltage of 5V can be used to operate the electronic component. It can conduct in a 2-bit manner.
MAX4504CSA Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
2-Bit
MAX4504CSA Applications
There are a lot of Maxim Integrated MAX4504CSA Analog Switches & Multiplexers ICs applications.
- Private Branch Exchange (PBX)
- Fiber In The Loop (FITL)
- Access Concentrators
- High reliability control systems
- Audio/video switches
- T1/E1 Terminals
- Optical Applications
- Isolation
- Industrial
- SONET
