Parameters |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2008 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
400Ohm |
Max Power Dissipation |
842mW |
Technology |
CMOS |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
1 |
Supply Voltage |
15V |
Terminal Pitch |
2.54mm |
Time@Peak Reflow Temperature-Max (s) |
20 |
Base Part Number |
MAX4508 |
Pin Count |
16 |
Operating Supply Voltage |
12V |
Number of Channels |
8 |
Number of Circuits |
1 |
Max Supply Voltage |
36V |
Min Supply Voltage |
9V |
Operating Supply Current |
1μA |
Propagation Delay |
350 ns |
Turn On Delay Time |
500 ns |
Logic Function |
Multiplexer |
Voltage - Supply, Single/Dual (±) |
9V~36V ±4.5V~20V |
Supply Type |
Dual, Single |
Supply Current-Max (Isup) |
0.6mA |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
250 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
400Ohm |
Min Dual Supply Voltage |
4.5V |
Multiplexer/Demultiplexer Circuit |
8:1 |
Off-state Isolation-Nom |
70 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
10pF 19pF |
On-state Resistance Match-Nom |
15Ohm |
Switch Time (Ton, Toff) (Max) |
275ns, 200ns |
Charge Injection |
2pC |
Channel-to-Channel Matching (ΔRon) |
15 Ω (Max) |
Crosstalk |
-62dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
275ns |
Switch-off Time-Max |
200ns |
Signal Current-Max |
0.03A |
Height Seated (Max) |
4.572mm |
Width |
7.62mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Mount |
Through Hole |
Mounting Type |
Through Hole |
Package / Case |
16-DIP (0.300, 7.62mm) |
Number of Pins |
16 |
MAX4508EPE Overview
Presented in 16-DIP (0.300, 7.62mm), this electrical component is convenient for overseas shipping. High reliability is achieved by using advanced packaging method Tube. The multiplexer is located in Through Hole. Multiplexers and demultiplexers have a ratio of 8:1. Increasing operating temperature to around -40°C~85°C TA. A total of 16 terminations have been recorded. High-quality output is provided by the electronic component's 8 channels. When the electronic component is given a voltage of 15V, it should be turned on and run. There is an electrical component included in the 16 series. There are 1 circuits in this multiplexer. Look for analog switch ic variants by searching with MAX4508. Analog switches have 400Ohm internal resistance. For functions related to 16 pins, please refer to the datasheets. An abnormal situation would be for the switch device to be supplied with a voltage greater than 36V. Analogue multiplexers of the Dual, Single supply type that are cost-effective. The lowest voltage fed to the electronic component should be 9V. An operating current of 1μA would be sufficient for this switch device. For this multiplexer, dual supply voltage is feasible, but it should not exceed 20V. With dual power supplies, you should attach at least 4.5V. Operating voltages range from 12V.
MAX4508EPE Features
8 Channels
1μA Supply Current
MAX4508EPE Applications
There are a lot of Maxim Integrated MAX4508EPE Analog Switches & Multiplexers ICs applications.
- Mechanical reed relay replacement
- Imaging
- Data switching
- Sample hold systems
- Digital access cross connects
- Optical Applications
- Switching Systems
- Modems
- Audio signal routing
- Video signal routing