Parameters |
Factory Lead Time |
1 Week |
Contact Plating |
Tin |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2008 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
400Ohm |
Max Power Dissipation |
696mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
15V |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
MAX4508 |
Pin Count |
16 |
Operating Supply Voltage |
12V |
Number of Channels |
8 |
Number of Circuits |
1 |
Max Supply Voltage |
36V |
Min Supply Voltage |
9V |
Operating Supply Current |
1μA |
Propagation Delay |
350 ns |
Turn On Delay Time |
500 ns |
Logic Function |
Multiplexer |
Voltage - Supply, Single/Dual (±) |
9V~36V ±4.5V~20V |
Supply Type |
Dual, Single |
Supply Current-Max (Isup) |
0.6mA |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
250 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
400Ohm |
Min Dual Supply Voltage |
4.5V |
High Level Output Current |
30mA |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
8:1 |
Off-state Isolation-Nom |
70 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
10pF 19pF |
On-state Resistance Match-Nom |
15Ohm |
Switch Time (Ton, Toff) (Max) |
275ns, 200ns |
Charge Injection |
2pC |
Channel-to-Channel Matching (ΔRon) |
15 Ω (Max) |
Crosstalk |
-62dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
275ns |
Switch-off Time-Max |
200ns |
Signal Current-Max |
0.03A |
Length |
9.9mm |
Width |
3.9mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
MAX4508ESE+T Overview
This electronic part is conveniently packaged in 16-SOIC (0.154, 3.90mm Width), making it easy to ship abroad. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. Surface Mount is where this multiplexer is located. Multiplexer and demultiplexer circuits have a number 8:1. Around -40°C~85°C TA is the extended operating temperature. In total, there are 16 terminations. A high-quality output is provided by the electrical component's 8 channels. With a 15V voltage supply, the electrical component should be turned on and run. Into the electrical component body are injected 16 pins. This multiplexer is composed of 1 circuits. Try searching for MAX4508 variants of the analog switch ic. A 400Ohm internal resistance characterizes this multiplexer. An abnormal situation would be for the switch device to be supplied with a voltage greater than 36V. A cost-effective Dual, Single supply type analogue multiplexer. The lowest voltage the electronic part should receive is 9V. An operating current of 1μA would be sufficient for this switch device. If put voltage greater than 20V on the multiplexer, damage may be caused to the device. When using dual power supplies, you should attach at least 4.5V. 12V operating voltages can be used with this electrical part.
MAX4508ESE+T Features
8 Channels
1μA Supply Current
MAX4508ESE+T Applications
There are a lot of Maxim Integrated MAX4508ESE+T Analog Switches & Multiplexers ICs applications.
- Audio signal routing
- Voice over IP/DSL – Integrated Access Devices, Smart
- Digital Cross-Connects
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Frame Relay Equipment
- Automotive applications
- Transmit
- Relay replacements
- Relay Replacement
- E1 Multiplexer