MAX4509CPE
| Parameters | |
|---|---|
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 10pF 14pF |
| On-state Resistance Match-Nom | 15Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 275ns, 200ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 15 Ω (Max) |
| Crosstalk | -62dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.03A |
| Length | 19.175mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2008 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 400Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Additional Feature | FAULT PROTECTED |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Pin Count | 16 |
| Operating Supply Voltage | 12V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 9V |
| Operating Supply Current | 1μA |
| Propagation Delay | 350 ns |
| Turn On Delay Time | 500 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Supply Current-Max (Isup) | 0.6mA |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 400Ohm |
| Min Dual Supply Voltage | 4.5V |
MAX4509CPE Overview
Packed in 16-DIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. High reliability is provided by advanced packaging method Tube. Through Hole is where this multiplexer is located. 4:1 is the ratio between multiplexers and demultiplexers. Increasing operating temperature to around 0°C~70°C TA. Total terminations are 16. A electrical component with 4 channels is capable of high-quality output. When a voltage supply of 15V is used, the electronic component should be turned on and run. Electronic part bodies are injected with 16 pins. Based on SP4T switching circuits, these analog multiplexers work. This multiplexer is composed of 2 circuits. This digital multiplexer has 400Ohm internal resistance. For details about the functions of 16 pins, please refer to the datasheets. A voltage higher than 36V should not normally be supplied to the switches. Digital switch that provides Dual, Single power at a cost-effective price. A low voltage of 9V should be applied to the electronic component. For this multiplexer to operate, 1μA current would be sufficient. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 20V. With dual power supplies, you should attach at least 4.5V. There is a voltage range of 12V operating voltages for the electrical part. There is also FAULT PROTECTED to look out for in this electronic part.
MAX4509CPE Features
4 Channels
Switch Circuit: SP4T
1μA Supply Current
Additional Features: FAULT PROTECTED
MAX4509CPE Applications
There are a lot of Maxim Integrated MAX4509CPE Analog Switches & Multiplexers ICs applications.
- Cellular phones
- Switching Systems
- SDH
- Sample hold systems
- Routers
- Industrial
- Access Concentrators
- Channel Banks
- Cross Connects
- Battery Powered Instruments
