MAX4509CSE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 400Ohm |
| Terminal Finish | Tin (Sn) |
| Additional Feature | FAULT PROTECTED |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Base Part Number | MAX4509 |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Operating Supply Voltage | 12V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 9V |
| Operating Supply Current | 1μA |
| Propagation Delay | 350 ns |
| Turn On Delay Time | 500 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Supply Current-Max (Isup) | 0.6mA |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 400Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 10pF 14pF |
| On-state Resistance Match-Nom | 15Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 275ns, 200ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 15 Ω (Max) |
| Crosstalk | -62dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.03A |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4509CSE+T Overview
Presented in 16-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. High reliability is achieved by using advanced packaging method Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. There is 4:1 ratio between the number of multiplexers and demultiplexers. Operating temperature around 0°C~70°C TA extended. In total, there are 16 terminations. By its 4 channels, the electronic component provides high-quality output. An 15V voltage supply should allow the electrical part to be turned on and run. There are 16 pins injected into the electronic part body. SP4T switching circuits are used in these analog switch ics. Circuits number 2 make up this analogue multiplexer. If you are looking for variants of the digital switch, trying search with MAX4509. It has an internal resistance of 400Ohm. normally, users should not supply switches with voltages higher than 36V. A analog switch ic that has a cost-effective Dual, Single supply type. 9V is the lowest voltage the electrical component should receive. It would be sufficient to run this analogue multiplexer with 1μA current. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 20V. It is recommended that you attach at least 4.5V to your dual power supply. A voltage of 12V can be used to operate the electronic component. Don't miss this electronic component's additional features, such as: FAULT PROTECTED.
MAX4509CSE+T Features
4 Channels
Switch Circuit: SP4T
1μA Supply Current
Additional Features: FAULT PROTECTED
MAX4509CSE+T Applications
There are a lot of Maxim Integrated MAX4509CSE+T Analog Switches & Multiplexers ICs applications.
- Digital Cross-Connects
- SONET
- Channel Banks
- Automatic test equipment
- Industrial
- HDTV
- Fiber In The Loop (FITL)
- PBX interfaces
- Communications systems
- Microprocessor controlled systems
