MAX4510EUT+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Number of Pins | 6 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1999 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 390Ohm |
| Terminal Finish | Gold (Au) - with Nickel (Ni) barrier |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.95mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4510 |
| Pin Count | 6 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 9V |
| Operating Supply Current | 50μA |
| Nominal Supply Current | 250μA |
| Max Supply Current | 175μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 200 ns |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 750 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 160Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 10pF 5pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 500ns, 175ns |
| Charge Injection | 1.5pC |
| Switch-on Time-Max | 500ns |
| Length | 2.9mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
MAX4510EUT+T Overview
Presented in SOT-23-6, this electrical component is convenient for overseas shipping. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. There is an analog multiplexer mounted in position Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Operation at a temperature around -40°C~85°C TA. Total terminations are 6. A 1 channel electronic part produces high-quality output. A 15V voltage supply should turn on and run the electronic component. The electronic part body is injected with 6 pins. Unlike digital switches, these are based on SPST - NC switching circuits. This multiplexer is composed of 1 circuits. Try searching with MAX4510 to find analog multiplexer variants. There is 390Ohm internal resistance in this digital multiplexer. The datasheets for the 6 pins explain the functions. An abnormal situation would be for the switch device to be supplied with a voltage greater than 36V. Analog switch ics with Dual, Single supply type are cost-effective. The lowest voltage fed to the electronic component should be 9V. This multiplexer would work with 50μA current. Putting voltage greater than 175μA on the multiplexer may cause damage. There is no problem with using dual supply voltage, but it should not exceed 20V. The voltage should be at least 4.5V if you are using dual power supplies. A voltage of 20V can be used to operate the electronic component.
MAX4510EUT+T Features
1 Channels
Switch Circuit: SPST - NC
50μA Supply Current
MAX4510EUT+T Applications
There are a lot of Maxim Integrated MAX4510EUT+T Analog Switches & Multiplexers ICs applications.
- Precision data acquisition
- T1/E1 Terminals
- Industrial control systems
- Isolation
- Multi-Line E1 Interface Cards
- Remote Powered Equipment
- Microprocessor controlled systems
- Medical
- Automatic test equipment
- Battery Powered Instruments
