banner_page

MAX4512CPE

500ns, 400ns SPST - NO 160Ohm DUAL Analog Switches BREAK-BEFORE-MAKE 16 Pins 500pA 15V 16-DIP (0.300, 7.62mm)


  • Manufacturer: Maxim Integrated
  • Nocochips NO: 503-MAX4512CPE
  • Package: 16-DIP (0.300, 7.62mm)
  • Datasheet: PDF
  • Stock: 366
  • Description: 500ns, 400ns SPST - NO 160Ohm DUAL Analog Switches BREAK-BEFORE-MAKE 16 Pins 500pA 15V 16-DIP (0.300, 7.62mm)(Kg)

Details

Tags

Parameters
Number of Functions 4
Supply Voltage 15V
Time@Peak Reflow Temperature-Max (s) 20
Output SEPARATE OUTPUT
Pin Count 16
Power Supplies 12/+-15V
Number of Channels 1
Number of Circuits 4
Max Supply Voltage 36V
Min Supply Voltage 9V
Voltage - Supply, Single/Dual (±) 9V~36V ±4.5V~18V
Neg Supply Voltage-Nom (Vsup) -15V
Max Dual Supply Voltage 18V
On-State Resistance (Max) 160Ohm
Min Dual Supply Voltage 4.5V
Multiplexer/Demultiplexer Circuit 1:1
Off-state Isolation-Nom 62 dB
Current - Leakage (IS(off)) (Max) 500pA
Channel Capacitance (CS(off), CD(off)) 10pF 5pF
On-state Resistance Match-Nom 3Ohm
Switch Circuit SPST - NO
Switch Time (Ton, Toff) (Max) 500ns, 400ns
Charge Injection 1.5pC
Crosstalk -66dB @ 1MHz
Switching BREAK-BEFORE-MAKE
Switch-on Time-Max 500ns
Normal Position NO
Length 19.175mm
Width 7.62mm
Radiation Hardening No
RoHS Status Non-RoHS Compliant
Mounting Type Through Hole
Package / Case 16-DIP (0.300, 7.62mm)
Surface Mount NO
Number of Pins 16
Operating Temperature 0°C~70°C TA
Packaging Tube
Published 2013
JESD-609 Code e0
Pbfree Code no
Part Status Obsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 16
ECCN Code EAR99
Terminal Finish Tin/Lead (Sn85Pb15)
Subcategory Multiplexer or Switches
Technology CMOS
Terminal Position DUAL
Peak Reflow Temperature (Cel) 240

MAX4512CPE Overview


Shipping overseas is convenient due to the electrical component's packing in 16-DIP (0.300, 7.62mm). High reliability is provided by advanced packaging method Tube. The multiplexer is located in Through Hole. Multiplexer and demultiplexer circuits have a number 1:1. Around 0°C~70°C TA is the extended operating temperature. The total number of terminations is 16. A 1 channel electronic part produces high-quality output. An 15V voltage supply should allow the electrical part to be turned on and run. An electrical component of this type can be found in the 16 series. These analog multiplexers are built based on SPST - NO switching circuits. The circuits in this analogue multiplexer number 4. To find out what the 16 pins do, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. Users should never supply a voltage higher than 36V to a switch device. It is recommended to use 9V as the lowest voltage for the electrical part. For this multiplexer, dual supply voltage is feasible, but it should not exceed 18V. In the case of dual power supplies, you should connect at least 4.5V. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer.

MAX4512CPE Features


1 Channels
Switch Circuit: SPST - NO

MAX4512CPE Applications


There are a lot of Maxim Integrated MAX4512CPE Analog Switches & Multiplexers ICs applications.

  • Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
  • Routers
  • Central office
  • FTTH
  • Ultrasound
  • SONET/SDH ADM
  • Wireless Local Loop
  • Avionics test equipment
  • Automatic test equipment
  • MP3 players

Write a review

Note: HTML is not translated!
    Bad           Good