MAX4512CSE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2002 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4512 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Qualification Status | Not Qualified |
| Power Supplies | 12/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~18V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| On-State Resistance (Max) | 160Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 10pF 5pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 500ns, 400ns |
| Charge Injection | 1.5pC |
| Crosstalk | -66dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 500ns |
| Normal Position | NO |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
MAX4512CSE+ Overview
Shipping overseas is convenient with the electronic component packed in 16-SOIC (0.154, 3.90mm Width). This high-reliability packaging method uses advanced packaging methods Tube. Multiplexers like this are mounted in the Surface Mount position. Multiplexers and demultiplexers have a number of circuits 1:1. Extended operating temperature around 0°C~70°C TA. In total, there have been 16 terminations. Due to its 1 channels, the electrical component produces high-quality output. Powered by a 15V voltage supply, the electrical part should be switched on and run. As part of its design, the 16 series is equipped with this electronic component. These analog multiplexers are built based on SPST - NO switching circuits. The multiplexer consists of 4 circuits. Try searching with MAX4512 if you're looking for variants. The analog multiplexer shown here is a typical Multiplexer or Switches. This analog switch ic utilizes SEPARATE OUTPUT output.
MAX4512CSE+ Features
1 Channels
Switch Circuit: SPST - NO
MAX4512CSE+ Applications
There are a lot of Maxim Integrated MAX4512CSE+ Analog Switches & Multiplexers ICs applications.
- Voice over IP/DSL – Integrated Access Devices, Smart
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Relay replacements
- Audio signal routing
- Communications systems
- Relay Replacement
- Public switching systems
- Fiber to the Home
- New designs requiring multiplexer functions
- SDH
