MAX4513CPE
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2002 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 160Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4513 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 12/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 9V |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~18V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 160Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 10pF 5pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 500ns, 400ns |
| Charge Injection | 1.5pC |
| Crosstalk | -66dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 500ns |
| Length | 19.175mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX4513CPE Overview
As the electronic part is packed in 16-DIP (0.300, 7.62mm), international shipping is convenient. High reliability is provided by advanced packaging method Tube. Mounted in Through Hole is this multiplexer. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Around 0°C~70°C TA is the extended operating temperature. In total, 16 terminations have occurred. High-quality output is provided by the electronic component's 1 channels. With a 15V voltage supply, the electrical component should be turned on and run. As part of the design of the 16 series, this electronic part has been incorporated into the system. SPST - NO/NC switching circuits are used in these analog switch ics. A total of 4 circuits make up this switch device. MAX4513 can be used to search for analog multiplexer variants. It has an internal resistance of 160Ohm. For functions related to 16 pins, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. A voltage higher than 36V should not normally be supplied to the switches. 9V is the lowest voltage that should be fed to the electronic electronic part. Despite this switch device's dual supply capability, its voltage should not exceed 18V. If you are using a dual power supply, you should attach at least 4.5V. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them.
MAX4513CPE Features
1 Channels
Switch Circuit: SPST - NO/NC
MAX4513CPE Applications
There are a lot of Maxim Integrated MAX4513CPE Analog Switches & Multiplexers ICs applications.
- Avionics
- SONET/SDH ADM
- Public switching systems
- Communication systems
- Digital Cross-Connects
- T1/E1 Terminals
- Cable PC
- PDAs
- Audio/video switches
- Microprocessor controlled systems
