MAX4513CSE
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2002 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 160Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4513 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Power Supplies | 12/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 18V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 280μA |
| Max Supply Current | 400μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 500 ns |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~18V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 400 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 160Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 10pF 5pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 500ns, 400ns |
| Charge Injection | 1.5pC |
| Crosstalk | -66dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4513CSE Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-SOIC (0.154, 3.90mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. Mounted in Surface Mount is this multiplexer. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operation at a temperature around 0°C~70°C TA. Totally, there are 16 terminations. The electronic part delivers high-quality output through its 1 channels. When a voltage supply of 15V is used, the electronic component should be turned on and run. A key feature of the 16 series is the inclusion of this electronic part as part of its design. Unlike digital switches, these are based on SPST - NO/NC switching circuits. The circuits in this analogue multiplexer number 4. If you are looking for variants of the digital switch, trying search with MAX4513. Analog switches have 160Ohm internal resistance. It is a typical Multiplexer or Switches analog multiplexer. It is generally not recommended to supply a voltage higher than 18V to the switch device in normal circumstances. Dual, Single supply type digital switch with a low cost. It is recommended to use 4.5V as the lowest voltage for the electrical part. Put voltage above 400μA on the multiplexer to cause damage. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 18V. The voltage should be at least 4.5V if you are using dual power supplies. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them.
MAX4513CSE Features
1 Channels
Switch Circuit: SPST - NO/NC
MAX4513CSE Applications
There are a lot of Maxim Integrated MAX4513CSE Analog Switches & Multiplexers ICs applications.
- Digital cross connects (DSX-1)
- Wireless Local Loop
- Access Concentrators
- Channel Banks
- Audio and video switching
- Precision test equipment
- Microprocessor Controlled Analog Systems
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Medical systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
