Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2002 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
160Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
696mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
1.27mm |
Base Part Number |
MAX4513 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
JESD-30 Code |
R-PDSO-G16 |
Operating Supply Voltage |
15V |
Number of Channels |
1 |
Number of Circuits |
4 |
Max Supply Voltage |
36V |
Min Supply Voltage |
9V |
Nominal Supply Current |
280μA |
Max Supply Current |
400μA |
Throw Configuration |
SPST |
Turn On Delay Time |
1 μs |
Voltage - Supply, Single/Dual (±) |
9V~36V ±4.5V~18V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
900 ns |
Max Dual Supply Voltage |
18V |
On-State Resistance (Max) |
160Ohm |
Min Dual Supply Voltage |
4.5V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
62 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
10pF 5pF |
On-state Resistance Match-Nom |
3Ohm |
Switch Circuit |
SPST - NO/NC |
Switch Time (Ton, Toff) (Max) |
500ns, 400ns |
Charge Injection |
1.5pC |
Crosstalk |
-66dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
500ns |
Height Seated (Max) |
1.75mm |
Length |
9.9mm |
Width |
3.9mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
MAX4513ESE+T Overview
Shipping overseas is convenient with the electronic component packed in 16-SOIC (0.154, 3.90mm Width). To ensure high reliability, a new packaging method Tape & Reel (TR) is used. There is an analog multiplexer mounted in position Surface Mount. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Around -40°C~85°C TA is the extended operating temperature. In total, there are 16 terminations. This electronic part offers high-quality output due to its 1 channels. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. As part of the design of the 16 series, this electronic part has been incorporated into the system. SPST - NO/NC switching circuits are used in these analog switch ics. It consists of 4 circuits. Look for analog switch ic variants by searching with MAX4513. It has an internal resistance of 160Ohm. There is Multiplexer or Switches analog multiplexer like this in the world. It is generally not recommended to supply a voltage higher than 36V to the switch device in normal circumstances. Analog switch ics with Dual, Single supply type are cost-effective. There should be 9V voltage fed to the electrical part below 9V. Put voltage above 400μA on the multiplexer to cause damage. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 18V. For dual power supplies, a voltage of at least 4.5V should be attached. There are SEPARATE OUTPUT outputs on this analog switch ic. Operating voltages range from 15V.
MAX4513ESE+T Features
1 Channels
Switch Circuit: SPST - NO/NC
MAX4513ESE+T Applications
There are a lot of Maxim Integrated MAX4513ESE+T Analog Switches & Multiplexers ICs applications.
- Industrial and process control systems
- High speed data transmission line cards
- Industrial control systems
- Residential Gateways, Home Gateway/Router
- Optical Applications
- PDAs
- Mechanical reed relay replacement
- E1 Multiplexer
- Multiplexers
- MP3 players