MAX4514CSA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2005 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 20Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 571mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 12V |
| Base Part Number | MAX4514 |
| Pin Count | 8 |
| Operating Supply Voltage | 9V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 20μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 240 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 150 ns |
| On-State Resistance (Max) | 20Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 14pF 14pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 2pC |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2V~12V |
| Normal Position | NO |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4514CSA+ Overview
Due to its 8-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. To ensure high reliability, a new packaging method Tube is used. Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have a number of circuits 1:1. Around 0°C~70°C TA is the extended operating temperature. In total, there have been 8 terminations. A electrical component with 1 channels is capable of high-quality output. An 12V voltage supply should allow the electrical part to be turned on and run. A total of 8 pins are injected into the electrical part body. On the other hand, analog switches can be constructed using SPST - NO switching circuits. The multiplexer consists of 1 circuits. Try searching for MAX4514 variants of the analog switch ic. There is 20Ohm internal resistance in this digital multiplexer. Datasheets for 8 pin functions are available upon request. In this analog multiplexer, the value is Multiplexer or Switches. Users should never supply a voltage higher than 12V to a switch device. Analogue multiplexer with a Single supply type that is cost-effective. There should be 2V voltage fed to the electrical part below 2V. An operating current of 1μA would be sufficient for this switch device. This analog switch requires a voltage of 2V~12V to drain from a single voltage supply. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. The electronic component can function from 9V.
MAX4514CSA+ Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
MAX4514CSA+ Applications
There are a lot of Maxim Integrated MAX4514CSA+ Analog Switches & Multiplexers ICs applications.
- SDH
- Digital Cross-Connects
- SDH/SONET multiplexers
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Medical
- MP3 players
- Communication systems
- Public switching systems
- E1 Multiplexer
- ATM
