MAX4514EPA
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1997 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 20Ohm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4514 |
| Pin Count | 8 |
| JESD-30 Code | R-PDIP-T8 |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Throw Configuration | SPST |
| Supply Type | Single |
| On-State Resistance (Max) | 20Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 14pF 14pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 2pC |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2V~12V |
| Normal Position | NO |
| Height Seated (Max) | 4.572mm |
| Length | 9.375mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4514EPA Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-DIP (0.300, 7.62mm). To ensure high reliability, a new packaging method Tube is used. In Through Hole, you'll find this switch device. Multiplexers and demultiplexers have a number of circuits 1:1. Operation at a temperature around -40°C~85°C TA. In total, 8 terminations have occurred. As a result of its 1 channels, this electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 5V voltage supply. An electrical component of this type can be found in the 8 series. Circuits based on SPST - NO switching are used to construct these analog switch ics. There are 1 circuits in this switch device. Try searching with MAX4514 if you're looking for variants. The internal resistance of this digital multiplexer is 20Ohm. In this analog multiplexer, the value is Multiplexer or Switches. Users should never supply a voltage higher than 12V to a switch device. Single supply type digital switch with a low cost. The lowest voltage fed to the electronic component should be 2V. For this multiplexer to operate, 1μA current would be sufficient. A voltage of 2V~12V is required for this switch device, which drains from a single voltage source.
MAX4514EPA Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
MAX4514EPA Applications
There are a lot of Maxim Integrated MAX4514EPA Analog Switches & Multiplexers ICs applications.
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Digital Cross-Connects
- High speed data transmission line cards
- Industrial and process control systems
- Relay Replacement
- Imaging
- Automotive applications
- Isolation
- Battery Powered Instruments
- 65 V DACs
