MAX4514ESA+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1996 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 20Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 571mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 12V |
| Base Part Number | MAX4514 |
| Pin Count | 8 |
| Operating Supply Voltage | 9V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 20μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 240 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 150 ns |
| On-State Resistance (Max) | 20Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 14pF 14pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 2pC |
| Voltage - Supply, Single (V+) | 2V~12V |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4514ESA+T Overview
Due to its 8-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. The advanced packaging method Tape & Reel (TR) provides high reliability. In Surface Mount, this analog switch is mounted. 1:1 is the ratio between multiplexers and demultiplexers. An extended operating temperature of -40°C~85°C TA degrees Celsius. There are 8 terminations totally. As a result of its 1 channels, this electronic component provides high-quality output. A 12V voltage supply should turn on and run the electronic component. An injection of 8 pins is performed into the body of the electrical component. Unlike digital switches, these are based on SPST - NO switching circuits. This multiplexer is composed of 1 circuits. MAX4514 can be used to search for analog multiplexer variants. As far as internal resistance is concerned, it has 20Ohm. To find out what the functions of 8 pins are, please refer to their datasheets. In normalcircumstances, users should not exceed 12V volts for the multiplexer. Analog switch ics with Single supply type are cost-effective. 2V is the lowest voltage that should be fed to the electronic electronic part. The analogue multiplexer could operate on 1μA current. A voltage of 2V~12V is required to drain this analog switch from a single voltage supply. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. The electronic component can function from 9V.
MAX4514ESA+T Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
MAX4514ESA+T Applications
There are a lot of Maxim Integrated MAX4514ESA+T Analog Switches & Multiplexers ICs applications.
- CSU
- SONET/SDH ADM
- Optical Applications
- Residential Gateways, Home Gateway/Router
- Cellular phones
- Video switching
- Medical
- Microprocessor Controlled Analog Systems
- Audio and video switching
- PCMCIA cards
