Parameters |
Contact Plating |
Tin |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
SC-74A, SOT-753 |
Number of Pins |
5 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
1997 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
5 |
ECCN Code |
EAR99 |
Resistance |
20Ohm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
571mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
1 |
Supply Voltage |
5V |
Time@Peak Reflow Temperature-Max (s) |
20 |
Base Part Number |
MAX4514 |
Pin Count |
5 |
Operating Supply Voltage |
9V |
Polarity |
Non-Inverting |
Number of Channels |
1 |
Max Supply Voltage |
12V |
Min Supply Voltage |
2V |
Operating Supply Current |
1μA |
Element Configuration |
Single |
Nominal Supply Current |
1μA |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
240 ns |
Turn-Off Delay Time |
150 ns |
On-State Resistance (Max) |
20Ohm |
High Level Output Current |
20mA |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
90 dB |
Current - Leakage (IS(off)) (Max) |
1nA |
Channel Capacitance (CS(off), CD(off)) |
14pF 14pF |
On-state Resistance Match-Nom |
1Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
150ns, 100ns |
Charge Injection |
2pC |
Switching |
BREAK-BEFORE-MAKE |
Voltage - Supply, Single (V+) |
2V~12V |
Normal Position |
NO |
Height |
1.3mm |
Length |
3mm |
Width |
1.75mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
MAX4514EUK-T Overview
As the electronic part is packed in SC-74A, SOT-753, international shipping is convenient. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. Surface Mount is where this multiplexer is located. Multiplexer and demultiplexer circuits have a number 1:1. An extended operating temperature of -40°C~85°C TA degrees Celsius. Totally, there are 5 terminations. A electrical component with 1 channels is capable of high-quality output. Turning on and running the electrical part should be easy with a 5V voltage supply. An injection of 5 pins is performed into the body of the electrical component. A SPST - NO switching circuit is used for these analog switches. Try searching for MAX4514 variants of the analog switch ic. As far as internal resistance is concerned, it has 20Ohm. For details about the functions of 5 pins, please refer to the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. A voltage higher than 12V should not normally be supplied to the switches. The lowest voltage the electronic part should receive is 2V. For this digital switch to work, 1μA current would suffice. This analog switch requires a voltage of 2V~12V to drain from a single voltage supply. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. The electrical part can be operated at 9V voltage levels.
MAX4514EUK-T Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
MAX4514EUK-T Applications
There are a lot of Maxim Integrated MAX4514EUK-T Analog Switches & Multiplexers ICs applications.
- Microprocessor controlled systems
- Multi-Line E1 Interface Cards
- Central office
- PDH Multiplexers
- Industrial control systems
- Multiplexers
- Audio and video routing
- SDH/SONET multiplexers
- ISDN NT1/TA
- Intelligent PBX