MAX4515CPA
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2005 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4515 |
| Pin Count | 8 |
| JESD-30 Code | R-PDIP-T8 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Operating Supply Current | 2μA |
| Throw Configuration | SPST |
| Supply Type | Single |
| On-State Resistance (Max) | 20Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 14pF 14pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 2pC |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2V~12V |
| Normal Position | NC |
| Height Seated (Max) | 4.572mm |
| Length | 9.375mm |
| Width | 7.62mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4515CPA Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-DIP (0.300, 7.62mm). High reliability is provided by advanced packaging method Tube. There is an analog multiplexer mounted in position Through Hole. Multiplexer and demultiplexer circuits have a number 1:1. Increasing operating temperature to around 0°C~70°C TA. 8 terminations have been made so far. High-quality output is provided by the electronic component's 1 channels. When the electronic component is given a voltage of 5V, it should be turned on and run. It is part of the design of the 8 series that this electronic component is included. Circuits based on SPST - NC switching are used to construct these analog switch ics. A total of 1 circuits make up this switch device. If you are looking for variants of the digital switch, trying search with MAX4515. There is 10Ohm internal resistance in this digital multiplexer. In this analog multiplexer, the value is Multiplexer or Switches. A cost-effective Single supply type analogue multiplexer. For this multiplexer to operate, 2μA current would be sufficient. A voltage of 2V~12V is required for this switch device, which drains from a single voltage source.
MAX4515CPA Features
1 Channels
Switch Circuit: SPST - NC
2μA Supply Current
MAX4515CPA Applications
There are a lot of Maxim Integrated MAX4515CPA Analog Switches & Multiplexers ICs applications.
- Audio signal routing
- Fault Tolerant Systems
- Residential Gateways, Home Gateway/Router
- Ultrasound
- Transmit
- SDH/SONET multiplexers
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Sample-and-hold systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Audio and video switching
