MAX4515CUK-T

150ns, 100ns SPST - NC 20Ohm DUAL Analog Switches BREAK-BEFORE-MAKE MAX4515 5 Pins 1nA 5V SC-74A, SOT-753

Manufacturer: Maxim Integrated
Nocochips NO: 503-MAX4515CUK-T
Package: SC-74A, SOT-753
Datasheet: PDF
Stock: 148
Description: 150ns, 100ns SPST - NC 20Ohm DUAL Analog Switches BREAK-BEFORE-MAKE MAX4515 5 Pins 1nA 5V SC-74A, SOT-753(Kg)

Details

Tags

Parameters
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	SC-74A, SOT-753
Number of Pins	5
Operating Temperature	0°C~70°C TA
Packaging	Tape & Reel (TR)
Published	2005
JESD-609 Code	e0
Pbfree Code	no
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	5
Resistance	10Ohm
Subcategory	Multiplexer or Switches
Max Power Dissipation	727mW
Technology	CMOS
Terminal Position	DUAL
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	240
Number of Functions	1
Supply Voltage	5V
Time@Peak Reflow Temperature-Max (s)	20
Base Part Number	MAX4515
Pin Count	5
Number of Channels	1
Max Supply Voltage	12V
Min Supply Voltage	2V
Operating Supply Current	2μA
Nominal Supply Current	20μA
Max Supply Current	1μA
Throw Configuration	SPST
Turn On Delay Time	100 ns
Supply Type	Single
Turn-Off Delay Time	150 ns
On-State Resistance (Max)	20Ohm
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	90 dB
Current - Leakage (IS(off)) (Max)	1nA
Channel Capacitance (CS(off), CD(off))	14pF 14pF
On-state Resistance Match-Nom	1Ohm
Switch Circuit	SPST - NC
Switch Time (Ton, Toff) (Max)	150ns, 100ns
Charge Injection	2pC
Switching	BREAK-BEFORE-MAKE
Voltage - Supply, Single (V+)	2V~12V
Normal Position	NC
Length	2.9mm
Radiation Hardening	No
REACH SVHC	Unknown
RoHS Status	Non-RoHS Compliant
Lead Free	Contains Lead

MAX4515CUK-T Overview

Presented in SC-74A, SOT-753, this electrical component is convenient for overseas shipping. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. In Surface Mount, you'll find this switch device. 1:1 is the ratio between multiplexers and demultiplexers. Around 0°C~70°C TA is the extended operating temperature. There are 5 terminations totally. A high-quality output is provided by the electrical component's 1 channels. An 5V voltage supply should allow the electrical part to be turned on and run. Into the electrical component body are injected 5 pins. On the other hand, analog switches can be constructed using SPST - NC switching circuits. Search with MAX4515 if you are looking for analog multiplexer variants. Internally, this switch multiplexer has a resistance of 10Ohm. For details about the functions of 5 pins, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. Users shouldn't supply more than 12V voltage to the switch device. The digital multiplexer has a low cost Single supply. 2V is the lowest voltage the electrical component should receive. 2μA current would be enough for this multiplexer to operate. A voltage of 2V~12V is required to drain this analog switch from a single voltage supply. It may damage the digital multiplexer if the voltage is higher than 1μA.