MAX4515EPA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2005 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 20Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | MAX4515 |
| Pin Count | 8 |
| Operating Supply Voltage | 9V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 2μA |
| Nominal Supply Current | 20μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 100 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 150 ns |
| On-State Resistance (Max) | 20Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 14pF 14pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 2pC |
| Voltage - Supply, Single (V+) | 2V~12V |
| Height Seated (Max) | 4.572mm |
| Length | 9.375mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
MAX4515EPA+ Overview
This electronic part is conveniently packaged in 8-DIP (0.300, 7.62mm), making it easy to ship abroad. Advanced packaging method Tube is used to provide high reliability. The multiplexer is located in Through Hole. Multiplexers and demultiplexers have the same number of circuits 1:1. Around -40°C~85°C TA is the extended operating temperature. In total, there have been 8 terminations. As a result of its 1 channels, this electronic component provides high-quality output. Powered by a 5V voltage supply, the electrical part should be switched on and run. 8 pins are injected to the electronic part body. Based on SPST - NC switching circuits, these analog multiplexers work. This multiplexer is composed of 1 circuits. MAX4515 can be used to search for analog multiplexer variants. This digital multiplexer has 20Ohm internal resistance. To find out what the 8 pins do, please refer to the datasheets. Users shouldn't supply more than 12V voltage to the switch device. An effective Single supply digital multiplexer. In order for the electronic part to function properly, the lowest voltage should be 2V. 2μA current would be enough for this multiplexer to operate. Analogue multiplexers require a 2V~12V voltage to drain from a single voltage supply. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. 9V operating voltages can be used with this electrical part.
MAX4515EPA+ Features
1 Channels
Switch Circuit: SPST - NC
2μA Supply Current
MAX4515EPA+ Applications
There are a lot of Maxim Integrated MAX4515EPA+ Analog Switches & Multiplexers ICs applications.
- DSLAMs
- Microprocessor controlled systems
- Cable Modem
- Power routing
- Audio and video routing
- Automatic test equipment
- Battery-powered systems
- Low-Voltage
- High-Voltage
- Ultrasound
