MAX4515ESA
| Parameters | |
|---|---|
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 10Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4515 |
| Pin Count | 8 |
| JESD-30 Code | R-PDSO-G8 |
| Operating Supply Voltage | 9V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 2μA |
| Nominal Supply Current | 20μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 100 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 150 ns |
| On-State Resistance (Max) | 20Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 14pF 14pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 2pC |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2V~12V |
| Normal Position | NC |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2005 |
MAX4515ESA Overview
Presented in 8-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. A high level of reliability can be achieved through the use of an advanced packaging method Tube. This analog switch is mounted in Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. An extended operating temperature of -40°C~85°C TA degrees Celsius. Totally, there are 8 terminations. A 1 channel electronic part produces high-quality output. Turning on and running the electrical part should be easy with a 5V voltage supply. An injection of 8 pins is performed into the body of the electrical component. Circuits based on SPST - NC switching are used to construct these analog switch ics. There are 1 circuits in this switch device. If you are looking for variants of the digital switch, trying search with MAX4515. There is 10Ohm internal resistance in this digital multiplexer. The analogue multiplexer in this example is a typical Multiplexer or Switches. Multiplexers should not be powered above 12V in normal situations. Single supply type digital switch with a low cost. In order for the electronic part to function properly, the lowest voltage should be 2V. The analogue multiplexer could operate on 2μA current. Analogue multiplexers require a 2V~12V voltage to drain from a single voltage supply. It may damage the digital multiplexer if the voltage is higher than 1μA. The electrical part can be operated at 9V voltage levels.
MAX4515ESA Features
1 Channels
Switch Circuit: SPST - NC
2μA Supply Current
MAX4515ESA Applications
There are a lot of Maxim Integrated MAX4515ESA Analog Switches & Multiplexers ICs applications.
- Digital access cross connects
- Medical
- Wireless Local Loop
- Mechanical reed relay replacement
- Audio/video switches
- Audio and video signal routing
- Video switching
- Low-Voltage
- Residential Gateways, Home Gateway/Router
- Industrial control systems
