MAX4516CSA
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1996 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 20Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 571mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4516 |
| Pin Count | 8 |
| JESD-30 Code | R-PDSO-G8 |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Operating Supply Current | 40μA |
| Nominal Supply Current | 40μA |
| Max Supply Current | 125μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 150 ns |
| Voltage - Supply, Single/Dual (±) | 2V~12V ±1V~6V |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 125 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 20Ohm |
| Min Dual Supply Voltage | 1V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 86 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 100ns, 75ns |
| Charge Injection | 10pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 75ns |
| Normal Position | NO |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4516CSA Overview
The electrical component comes in 8-SOIC (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. This packaging method provides high reliability because it uses advanced packaging techniques. Mounted in Surface Mount is this multiplexer. Multiplexers and demultiplexers have a ratio of 1:1. Operation at a temperature around 0°C~70°C TA. In total, there have been 8 terminations. The electronic part delivers high-quality output through its 1 channels. Powered by a 5V voltage supply, the electrical part should be switched on and run. An electrical component like this is included in the 8 series. SPST - NO switching circuits are used in these analog switch ics. A 1 circuit is present in this switch device. MAX4516 can be used to search for analog multiplexer variants. A 20Ohm internal resistance characterizes this multiplexer. Theswitch device is a typical Multiplexer or Switches. Analogue multiplexer with a Dual supply type that is cost-effective. In order to operate this switch device, it would need a current of 40μA. The analogue multiplexer may be damaged if voltage is greater than 125μA. If put voltage greater than 6V on the multiplexer, damage may be caused to the device. When using dual power supplies, you should attach at least 1V. 5V operating voltages can be used with this electrical part.
MAX4516CSA Features
1 Channels
Switch Circuit: SPST - NO
40μA Supply Current
MAX4516CSA Applications
There are a lot of Maxim Integrated MAX4516CSA Analog Switches & Multiplexers ICs applications.
- SONET/SDH ADM
- Medical systems
- USB 1.1 signal switching circuits
- Video switching
- Central office
- Sample hold systems
- Fiber to the Home
- Fault Tolerant Systems
- Transmit
- Isolation
