MAX4516CUK-T
| Parameters | |
|---|---|
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Weight | 29.993795mg |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1996 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Resistance | 20Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 571mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4516 |
| Pin Count | 5 |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Operating Supply Current | 40μA |
| Max Supply Current | 125μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 100 ns |
| Voltage - Supply, Single/Dual (±) | 2V~12V ±1V~6V |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 75 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 20Ohm |
| Min Dual Supply Voltage | 1V |
| High Level Output Current | 20mA |
| Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 86 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 100ns, 75ns |
| Charge Injection | 10pC |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Length | 2.9mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4516CUK-T Overview
The electronic part can be shipped overseas conveniently because it is packaged in SC-74A, SOT-753. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). The multiplexer is located in Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. An extended operating temperature of 0°C~70°C TA degrees Celsius. Total terminations are 5. A electrical component with 1 channels is capable of high-quality output. A 5V voltage supply should turn on and run the electronic component. A total of 5 pins are injected into the body of the electronic part. A SPST - NO switching circuit is used to build these analog multiplexers. Look for analog switch ic variants by searching with MAX4516. Analog switches have 20Ohm internal resistance. Datasheets for functions of 5 pins are available. It is a typical Multiplexer or Switches analog multiplexer. Digital switch that provides Dual power at a cost-effective price. The analogue multiplexer could operate on 40μA current. If put voltage greater than 125μA on the device, damage may be caused to the analogue multiplexer. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 6V. In the case of dual power supplies, you should connect at least 1V. It can operate from 5V operating voltages.
MAX4516CUK-T Features
1 Channels
Switch Circuit: SPST - NO
40μA Supply Current
MAX4516CUK-T Applications
There are a lot of Maxim Integrated MAX4516CUK-T Analog Switches & Multiplexers ICs applications.
- Audio and video routing
- RGB switches
- SONET/SDH ADM
- Optical Applications
- Video switching
- Audio and video signal routing
- Isolation
- Automatic test equipment
- Microprocessor Controlled Analog Systems
- Battery Powered Systems
