MAX4517CUK+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Weight | 29.993795mg |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1996 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Resistance | 20Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 571mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4517 |
| Pin Count | 5 |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Operating Supply Current | 40μA |
| Max Supply Current | 125μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 100 ns |
| Voltage - Supply, Single/Dual (±) | 2V~12V ±1V~6V |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 75 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 20Ohm |
| Min Dual Supply Voltage | 1V |
| Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 86 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 100ns, 75ns |
| Charge Injection | 10pC |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Length | 2.9mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
MAX4517CUK+T Overview
As the electronic part is packed in SC-74A, SOT-753, international shipping is convenient. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Increasing operating temperature to around 0°C~70°C TA. There are 5 terminations totally. Due to its 1 channels, the electrical component produces high-quality output. If the voltage supply is 5V volts, the electrical component should be turned on and run. An electrical component of this type can be found in the 5 series. Multiplexers built on a SPST - NC switching circuit are built. MAX4517 can be used to search for analog multiplexer variants. The internal resistance of this digital multiplexer is 20Ohm. For details about the functions of 5 pins, please refer to the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. The digital multiplexer has a low cost Dual supply. The switch device would be able to operate with 40μA current. The switch multiplexer may be damaged if it is exposed to voltage greater than 125μA. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 6V. When using dual power supplies, you should attach at least 1V. There is a voltage range of 5V operating voltages for the electrical part.
MAX4517CUK+T Features
1 Channels
Switch Circuit: SPST - NC
40μA Supply Current
MAX4517CUK+T Applications
There are a lot of Maxim Integrated MAX4517CUK+T Analog Switches & Multiplexers ICs applications.
- Audio/video switches
- PBX interfaces
- Multiplexers
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Channel Banks
- Isolation
- Data Acquisition Systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- High reliability control systems
- Modems
