MAX4517EUK-T
| Parameters | |
|---|---|
| Throw Configuration | SPST |
| Turn On Delay Time | 100 ns |
| Voltage - Supply, Single/Dual (±) | 2V~12V ±1V~6V |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 75 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 20Ohm |
| Min Dual Supply Voltage | 1V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 86 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 100ns, 75ns |
| Charge Injection | 10pC |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Length | 2.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1996 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Resistance | 20Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 571mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4517 |
| Pin Count | 5 |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Operating Supply Current | 40μA |
| Nominal Supply Current | 40μA |
| Max Supply Current | 125μA |
MAX4517EUK-T Overview
As the electronic part is packed in SC-74A, SOT-753, international shipping is convenient. This packaging method provides high reliability because it uses advanced packaging techniques. A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. The operating temperature is extended to around -40°C~85°C TA. Totally, there are 5 terminations. The electronic part delivers high-quality output through its 1 channels. Powered by a 5V voltage supply, the electrical part should be switched on and run. The electronic part body is injected with 5 pins. The analog switch ics are built using SPST - NC switching circuits. This multiplexer is composed of 1 circuits. Try searching for the analog switch ic with MAX4517 if you are looking for variants. There is 20Ohm internal resistance in this digital multiplexer. The datasheets for the 5 pins explain the functions. There is Multiplexer or Switches analog multiplexer like this in the world. The digital multiplexer has a low cost Dual supply. In order to operate this switch device, it would need a current of 40μA. The analogue multiplexer may be damaged if voltage is greater than 125μA. For this multiplexer, dual supply voltage is feasible, but it should not exceed 6V. It is recommended that you attach at least 1V to your dual power supply. 5V operating voltages are supported by the electronic component.
MAX4517EUK-T Features
1 Channels
Switch Circuit: SPST - NC
40μA Supply Current
MAX4517EUK-T Applications
There are a lot of Maxim Integrated MAX4517EUK-T Analog Switches & Multiplexers ICs applications.
- Central office
- PCMCIA cards
- New designs requiring multiplexer functions
- DSUs
- PBX interfaces
- HDTV
- Digital Cross-Connects
- High-Voltage
- Power routing
- Audio and video signal routing
