MAX4518CPD
| Parameters | |
|---|---|
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Max Power Dissipation | 800mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4518 |
| Pin Count | 14 |
| Operating Supply Voltage | 12V |
| Number of Channels | 4 |
| Number of Circuits | 1 |
| Max Supply Voltage | 15V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Throw Configuration | 4PST |
| Propagation Delay | 150 ns |
| Turn On Delay Time | 500 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 2V~15V ±2.7V~8V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 400 ns |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 2.7V |
| Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 16pF |
| On-state Resistance Match-Nom | 4Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 5pC (Max) |
| Channel-to-Channel Matching (ΔRon) | 4 Ω (Max) |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Height | 4.45mm |
| Length | 19.43mm |
| Width | 7.87mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
MAX4518CPD Overview
Shipping overseas is convenient due to the electrical component's packing in 14-DIP (0.300, 7.62mm). High reliability is ensured by the advanced packaging method Tube. The multiplexer is located in Through Hole. Multiplexer and demultiplexer circuits have a number 4:1. Operation at a temperature around 0°C~70°C TA. In total, 14 terminations have occurred. The electronic part delivers high-quality output through its 4 channels. If the voltage supply is 5V volts, the electrical component should be turned on and run. Into the electrical component body are injected 14 pins. The analog switch ics are built using SP4T switching circuits. The multiplexer consists of 1 circuits. Search with MAX4518 if you are looking for analog multiplexer variants. An switch multiplexer with 100Ohm internal resistance has a value of 100Ohm. The datasheets for the 14 pins explain the functions. In normalcircumstances, users should not exceed 15V volts for the multiplexer. A cost-effective Dual, Single supply type analogue multiplexer. 2.7V is the lowest voltage the electrical component should receive. This digital switch can be operated with a current of 1μA. For this switch, a dual supply voltage is feasible, but it must not exceed 8VYou should attach at least 2.7V voltage if you are using dual power supply. 12V operating voltages can be used with this electrical part.
MAX4518CPD Features
4 Channels
Switch Circuit: SP4T
1μA Supply Current
MAX4518CPD Applications
There are a lot of Maxim Integrated MAX4518CPD Analog Switches & Multiplexers ICs applications.
- Audio/video switches
- Industrial control systems
- Battery Powered Instruments
- Sample hold systems
- Optical Applications
- SDH/SONET multiplexers
- Data Acquisition Systems
- Switching Systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Cell phones
