MAX4518CSD+T
| Parameters | |
|---|---|
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 5pC (Max) |
| Channel-to-Channel Matching (ΔRon) | 4 Ω (Max) |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Length | 8.65mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | MAX4518 |
| Pin Count | 14 |
| Power Supplies | 3/5/+-5V |
| Number of Channels | 4 |
| Number of Circuits | 1 |
| Max Supply Voltage | 15V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 2V~15V ±2.7V~8V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 2.7V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 16pF |
| On-state Resistance Match-Nom | 4Ohm |
| Switch Circuit | SP4T |
MAX4518CSD+T Overview
The electronic component is convenient to ship overseas because it is packed in a 14-SOIC (0.154, 3.90mm Width). The advanced packaging method Tape & Reel (TR) provides high reliability. In Surface Mount, you'll find this switch device. In the multiplexer and demultiplexer, 4:1 represents the number of circuits. Operation at a temperature around 0°C~70°C TA. Total terminations are 14. As a result of its 4 channels, this electronic component provides high-quality output. When the electronic component is given a voltage of 5V, it should be turned on and run. An electrical component like this is included in the 14 series. These analog multiplexers are built based on SP4T switching circuits. A 1 circuit is present in this switch device. Try searching with MAX4518 if you're looking for variants. Internally, this switch multiplexer has a resistance of 100Ohm. In a normalsituation, users should not supply the switches with voltage higher than 15V. Dual, Single supply type digital switch with a low cost. The lowest voltage fed to the electronic component should be 2.7V. 1μA current would be enough for this multiplexer to operate. There is no problem with using dual supply voltage, but it should not exceed 8V. A dual power supply should have at least 2.7V voltage attached.
MAX4518CSD+T Features
4 Channels
Switch Circuit: SP4T
1μA Supply Current
MAX4518CSD+T Applications
There are a lot of Maxim Integrated MAX4518CSD+T Analog Switches & Multiplexers ICs applications.
- Isolation
- 65 V DACs
- Public switching systems
- FTTH
- Audio signal routing
- Low-Voltage
- SONET/SDH ADM
- Channel Banks
- Residential Gateways, Home Gateway/Router
- Battery-powered systems
