banner_page

MAX4519CPD+

150ns, 150ns DPST - NO 100Ohm DUAL Analog Switches 14 Pins 100pA 5V 14-DIP (0.300, 7.62mm)


  • Manufacturer: Maxim Integrated
  • Nocochips NO: 503-MAX4519CPD+
  • Package: 14-DIP (0.300, 7.62mm)
  • Datasheet: PDF
  • Stock: 672
  • Description: 150ns, 150ns DPST - NO 100Ohm DUAL Analog Switches 14 Pins 100pA 5V 14-DIP (0.300, 7.62mm)(Kg)

Details

Tags

Parameters
Current - Leakage (IS(off)) (Max) 100pA
Channel Capacitance (CS(off), CD(off)) 5pF 10pF
On-state Resistance Match-Nom 4Ohm
Switch Circuit DPST - NO
Switch Time (Ton, Toff) (Max) 150ns, 150ns
Charge Injection 5pC (Max)
Channel-to-Channel Matching (ΔRon) 4 Ω (Max)
Crosstalk -92dB @ 100kHz
Switch-on Time-Max 150ns
Switch-off Time-Max 150ns
Length 19.05mm
Radiation Hardening No
RoHS Status ROHS3 Compliant
Package / Case 14-DIP (0.300, 7.62mm)
Surface Mount NO
Number of Pins 14
Operating Temperature 0°C~70°C TA
Published 1999
JESD-609 Code e3
Pbfree Code yes
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 14
ECCN Code EAR99
Resistance 100Ohm
Terminal Finish Matte Tin (Sn)
Technology CMOS
Terminal Position DUAL
Terminal Form THROUGH-HOLE
Peak Reflow Temperature (Cel) 260
Number of Functions 1
Supply Voltage 5V
Pin Count 14
Number of Channels 2
Number of Circuits 2
Max Supply Voltage 15V
Min Supply Voltage 2.7V
Analog IC - Other Type DIFFERENTIAL MULTIPLEXER
Voltage - Supply, Single/Dual (±) 2.7V~15V ±2.7V~8V
Neg Supply Voltage-Nom (Vsup) -5V
Max Dual Supply Voltage 8V
On-State Resistance (Max) 100Ohm
Min Dual Supply Voltage 2.7V
Multiplexer/Demultiplexer Circuit 2:1
Off-state Isolation-Nom 75 dB

MAX4519CPD+ Overview


Presented in 14-DIP (0.300, 7.62mm), this electrical component is convenient for overseas shipping. Multiplexers and demultiplexers have a ratio of 2:1. Increasing operating temperature to around 0°C~70°C TA. The total number of terminations is 14. Due to its 2 channels, the electrical component produces high-quality output. An 5V voltage supply should allow the electrical part to be turned on and run. There is an electrical component included in the 14 series. Circuits based on DPST - NO switching are used to construct these analog switch ics. This multiplexer is composed of 2 circuits. This digital multiplexer has 100Ohm internal resistance. Datasheets for 14 pin functions are available upon request. Users shouldn't supply more than 15V voltage to the switch device. In order for the electronic part to function properly, the lowest voltage should be 2.7V. Despite this switch device's dual supply capability, its voltage should not exceed 8V. In the case of dual power supplies, you should connect at least 2.7V. A DIFFERENTIAL MULTIPLEXER analog IC is integrated into the board.

MAX4519CPD+ Features


2 Channels
Switch Circuit: DPST - NO

MAX4519CPD+ Applications


There are a lot of Maxim Integrated MAX4519CPD+ Analog Switches & Multiplexers ICs applications.

  • Fault Tolerant Systems
  • Relay replacements
  • SONET
  • Cellular phones
  • Voice over IP/DSL – Integrated Access Devices, Smart
  • Residential Gateways, Home Gateway/Router
  • T1/E1 Terminals
  • Avionics
  • DVD-R
  • Existing multiplexer applications (both fault-protected and nonfault-protected)

Write a review

Note: HTML is not translated!
    Bad           Good