MAX4519CSD
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Terminal Finish | TIN LEAD |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Pin Count | 14 |
| JESD-30 Code | R-PDSO-G14 |
| Qualification Status | COMMERCIAL |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Voltage - Supply, Single/Dual (±) | 2V~15V ±2.7V~8V |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| On-State Resistance (Max) | 100Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 10pF |
| On-state Resistance Match-Nom | 4Ohm |
| Switch Circuit | DPST - NO |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 5pC (Max) |
| Channel-to-Channel Matching (ΔRon) | 4 Ω (Max) |
| Crosstalk | -92dB @ 100kHz |
| Switch-on Time-Max | 150ns |
| Switch-off Time-Max | 150ns |
| Height Seated (Max) | 1.75mm |
| Length | 8.65mm |
| Width | 3.9mm |
| RoHS Status | Non-RoHS Compliant |
MAX4519CSD Overview
Packed in 14-SOIC (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. Advanced packaging method Tube is used to provide high reliability. Multiplexers like this are mounted in the Surface Mount position. Multiplexer and demultiplexer circuits have a number 2:1. Operation at a temperature around 0°C~70°C TA. Total terminations are 14. By its 2 channels, the electronic component provides high-quality output. An 5V voltage supply should allow the electrical part to be turned on and run. The electrical component body receives 14 pins. A DPST - NO switching circuit is used to build these analog multiplexers. This multiplexer is composed of 2 circuits. With a DIFFERENTIAL MULTIPLEXER analog IC integrated into the board.
MAX4519CSD Features
2 Channels
Switch Circuit: DPST - NO
MAX4519CSD Applications
There are a lot of Rochester Electronics, LLC MAX4519CSD Analog Switches & Multiplexers ICs applications.
- SDH/SONET multiplexers
- New designs requiring multiplexer functions
- Intelligent PBX
- High speed data transmission line cards
- MP3 players
- Voice over IP/DSL – Integrated Access Devices, Smart
- Audio signal routing
- Mechanical reed relay replacement
- T1/E1 Terminals
- HDTV
