Parameters |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
14-SOIC (0.154, 3.90mm Width) |
Number of Pins |
14 |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tube |
Published |
1999 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
14 |
ECCN Code |
EAR99 |
Resistance |
100Ohm |
Terminal Finish |
Tin/Lead (Sn85Pb15) |
Max Power Dissipation |
640mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
1 |
Supply Voltage |
5V |
Time@Peak Reflow Temperature-Max (s) |
20 |
Base Part Number |
MAX4519 |
Pin Count |
14 |
Power Supplies |
3/5/+-5V |
Number of Channels |
2 |
Number of Circuits |
2 |
Max Supply Voltage |
8V |
Min Supply Voltage |
2.7V |
Operating Supply Current |
1μA |
Max Supply Current |
1μA |
Turn On Delay Time |
150 ns |
Logic Function |
Multiplexer |
Voltage - Supply, Single/Dual (±) |
2V~15V ±2.7V~8V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
150 ns |
Max Dual Supply Voltage |
8V |
On-State Resistance (Max) |
100Ohm |
Min Dual Supply Voltage |
2.7V |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
75 dB |
Current - Leakage (IS(off)) (Max) |
100pA |
Channel Capacitance (CS(off), CD(off)) |
5pF 10pF |
On-state Resistance Match-Nom |
4Ohm |
Switch Circuit |
DPST - NO |
Switch Time (Ton, Toff) (Max) |
150ns, 150ns |
Charge Injection |
5pC (Max) |
Channel-to-Channel Matching (ΔRon) |
4 Ω (Max) |
Crosstalk |
-92dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Height Seated (Max) |
1.75mm |
Length |
8.65mm |
Width |
3.9mm |
Radiation Hardening |
No |
RoHS Status |
Non-RoHS Compliant |
MAX4519CSD Overview
Presented in 14-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. High reliability is achieved by using advanced packaging method Tube. Multiplexers like this are mounted in the Surface Mount position. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. The operating temperature is extended to around 0°C~70°C TA. In total, there are 14 terminations. Due to its 2 channels, the electrical component produces high-quality output. It is safe to turn on and run the electronic component with a 5V voltage supply. An injection of 14 pins is performed into the body of the electrical component. The analog switch ics are built using DPST - NO switching circuits. It consists of 2 circuits. If you are looking for variants of the digital switch, trying search with MAX4519. Analog switches have 100Ohm internal resistance. You can find the functions of the 14 pins in the datasheets. Multiplexers should not be powered above 8V in normal situations. The analog switch ic is of the Dual, Single supply type and is cost-effective. The lowest voltage the electronic part should receive is 2.7V. An operating current of 1μA would be sufficient for this switch device. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 8V. If you are using a dual power supply, you should attach at least 2.7V.
MAX4519CSD Features
2 Channels
Switch Circuit: DPST - NO
1μA Supply Current
MAX4519CSD Applications
There are a lot of Maxim Integrated MAX4519CSD Analog Switches & Multiplexers ICs applications.
- Battery-powered systems
- Power routing
- Central office
- Fiber to the Home
- RGB switches
- Frame Relay Equipment
- E1 Multiplexer
- Ultrasound
- MP3 players
- SDH