MAX4519EEE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SSOP (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 288.002805mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Max Power Dissipation | 762mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.635mm |
| Pin Count | 16 |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Max Supply Voltage | 15V |
| Min Supply Voltage | 2.7V |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Max Supply Current | 1μA |
| Turn On Delay Time | 150 ns |
| Voltage - Supply, Single/Dual (±) | 2V~15V ±2.7V~8V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 2.7V |
| Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 10pF |
| On-state Resistance Match-Nom | 4Ohm |
| Switch Circuit | DPST - NO |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 5pC (Max) |
| Channel-to-Channel Matching (ΔRon) | 4 Ω (Max) |
| Crosstalk | -92dB @ 100kHz |
| Height | 1.55mm |
| Length | 4.98mm |
| Width | 3.99mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4519EEE+ Overview
The electrical component comes in 16-SSOP (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. This packaging method provides high reliability because it uses advanced packaging techniques. Multiplexers like this are mounted in the Surface Mount position. Multiplexers and demultiplexers have a ratio of 2:1. Increasing operating temperature to around -40°C~85°C TA. Total terminations are 16. As a result of its 2 channels, this electronic component provides high-quality output. Turning on and running the electrical part should be easy with a 5V voltage supply. An electrical component like this is included in the 16 series. DPST - NO switching circuits are used in these analog switch ics. There are 2 circuits in this multiplexer. An switch multiplexer with 100Ohm internal resistance has a value of 100Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. In normalcircumstances, users should not exceed 15V volts for the multiplexer. Analog switch ics with Dual, Single supply type are cost-effective. In order for the electronic part to function properly, the lowest voltage should be 2.7V. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. If put voltage greater than 8V on the multiplexer, damage may be caused to the device. When using dual power supplies, you should attach at least 2.7V. It is integrated with a DIFFERENTIAL MULTIPLEXER analog IC.
MAX4519EEE+ Features
2 Channels
Switch Circuit: DPST - NO
MAX4519EEE+ Applications
There are a lot of Maxim Integrated MAX4519EEE+ Analog Switches & Multiplexers ICs applications.
- MP3 players
- Voice over IP/DSL – Integrated Access Devices, Smart
- Digital access cross connects
- HDTV
- Low-Voltage
- 65 V DACs
- ISDN NT1/TA
- Avionics test equipment
- RGB switches
- High reliability control systems
