MAX4519ESD
| Parameters | |
|---|---|
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4519 |
| Pin Count | 14 |
| Power Supplies | 3/5/+-5V |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Max Supply Voltage | 8V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 150 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 2V~15V ±2.7V~8V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 2.7V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 10pF |
| On-state Resistance Match-Nom | 4Ohm |
| Switch Circuit | DPST - NO |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 5pC (Max) |
| Channel-to-Channel Matching (ΔRon) | 4 Ω (Max) |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Height Seated (Max) | 1.75mm |
| Length | 8.65mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
MAX4519ESD Overview
The electrical component comes in 14-SOIC (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. High reliability is ensured by the advanced packaging method Tube. Surface Mount is where this multiplexer is located. There is 2:1 ratio between the number of multiplexers and demultiplexers. Operating temperature around -40°C~85°C TA extended. In total, 14 terminations have occurred. A 2 channel electronic part produces high-quality output. A 5V voltage supply should turn on and run the electronic component. A total of 14 pins are injected into the electrical part body. A DPST - NO switching circuit is used for these analog switches. There are 2 circuits in this multiplexer. Try searching for MAX4519 variants of the analog switch ic. Internally, this switch multiplexer has a resistance of 100Ohm. The functions of 14 pins can be found in the datasheets. Users should never supply a voltage higher than 8V to a switch device. The digital multiplexer has a low cost Dual, Single supply. 2.7V is the lowest voltage the electrical component should receive. This multiplexer would work with 1μA current. Putting voltage greater than 1μA on the multiplexer may cause damage. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 8V. In the case of dual power supplies, you should connect at least 2.7V.
MAX4519ESD Features
2 Channels
Switch Circuit: DPST - NO
1μA Supply Current
MAX4519ESD Applications
There are a lot of Maxim Integrated MAX4519ESD Analog Switches & Multiplexers ICs applications.
- Power routing
- Private Branch Exchange (PBX)
- High-Voltage
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Video signal routing
- Industrial and process control systems
- Central office
- Communication systems
- PBXs
- MP3 players
