MAX4520EUA
| Parameters | |
|---|---|
| Width | 3mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 160Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 330mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4520 |
| Pin Count | 8 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 9V |
| Operating Supply Current | 50μA |
| Nominal Supply Current | 250μA |
| Max Supply Current | 175μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 200 ns |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 750 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 160Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 10pF 5pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 500ns, 175ns |
| Charge Injection | 1.5pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 600ns |
| Switch-off Time-Max | 250ns |
| Normal Position | NO |
| Length | 3mm |
MAX4520EUA Overview
Shipping overseas is convenient due to the electrical component's packing in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. It is mounted in the position Surface Mount. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operation at a temperature around -40°C~85°C TA. In total, 8 terminations have occurred. The electronic part provides high-quality output because it has 1 channels. A 15V voltage supply should turn on and run the electronic component. This electronic part can be found in the 8 series. Multiplexers built on a SPST - NO switching circuit are built. The multiplexer consists of 1 circuits. Try searching with MAX4520 to find analog multiplexer variants. An switch multiplexer with 160Ohm internal resistance has a value of 160Ohm. Datasheets for functions of 8 pins are available. It is a typical Multiplexer or Switches analog multiplexer. normally, users should not supply switches with voltages higher than 36V. Analogue multiplexers of the Dual, Single supply type that are cost-effective. There should be 9V voltage fed to the electrical part below 9V. 50μA current would be enough for this multiplexer to operate. If you put voltage higher than 175μA on the digital multiplexer, damage may occur. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 20V. For dual power supplies, a voltage of at least 4.5V should be attached. It can operate from 20V operating voltages.
MAX4520EUA Features
1 Channels
Switch Circuit: SPST - NO
50μA Supply Current
MAX4520EUA Applications
There are a lot of Maxim Integrated MAX4520EUA Analog Switches & Multiplexers ICs applications.
- Cellular phones
- Digital cross connects (DSX-1)
- PBX interfaces
- PBXs
- DSUs
- Audio/video switches
- Automotive applications
- Automatic test equipment
- Frame Relay Equipment
- Digital access cross connects
