MAX4520EUT-T

500ns, 175ns SPST - NO 160Ohm Analog Switches BREAK-BEFORE-MAKE MAX4520 6 Pins 500pA 15V SOT-23-6

Manufacturer: Maxim Integrated
Nocochips NO: 503-MAX4520EUT-T
Package: SOT-23-6
Datasheet: PDF
Stock: 950
Description: 500ns, 175ns SPST - NO 160Ohm Analog Switches BREAK-BEFORE-MAKE MAX4520 6 Pins 500pA 15V SOT-23-6(Kg)

Details

Tags

Parameters
Contact Plating	Gold
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	SOT-23-6
Number of Pins	6
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	1999
JESD-609 Code	e0
Pbfree Code	no
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	6
ECCN Code	EAR99
Resistance	390Ohm
Subcategory	Multiplexer or Switches
Max Power Dissipation	696mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	240
Number of Functions	1
Supply Voltage	15V
Terminal Pitch	0.95mm
Time@Peak Reflow Temperature-Max (s)	20
Base Part Number	MAX4520
Pin Count	6
Operating Supply Voltage	20V
Polarity	Non-Inverting
Number of Channels	1
Number of Circuits	1
Max Supply Voltage	36V
Min Supply Voltage	9V
Operating Supply Current	50μA
Nominal Supply Current	250μA
Max Supply Current	175μA
Number of Bits	4
Throw Configuration	SPST
Turn On Delay Time	200 ns
Voltage - Supply, Single/Dual (±)	9V~36V ±4.5V~20V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	750 ns
Max Dual Supply Voltage	20V
On-State Resistance (Max)	160Ohm
Min Dual Supply Voltage	4.5V
High Level Output Current	30mA
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	62 dB
Current - Leakage (IS(off)) (Max)	500pA
Channel Capacitance (CS(off), CD(off))	10pF 5pF
Switch Circuit	SPST - NO
Switch Time (Ton, Toff) (Max)	500ns, 175ns
Charge Injection	1.5pC
Switching	BREAK-BEFORE-MAKE
Switch-off Time-Max	250ns
Normal Position	NO
Length	2.9mm
Radiation Hardening	No
REACH SVHC	Unknown
RoHS Status	Non-RoHS Compliant
Lead Free	Contains Lead

MAX4520EUT-T Overview

Packed in SOT-23-6, the electronic component is convenient for shipping overseas. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). In Surface Mount, you'll find this switch device. Multiplexers and demultiplexers have a number of circuits 1:1. Operation at a temperature around -40°C~85°C TA. A total of 6 terminations have been recorded. A high-quality output is provided by the electrical component's 1 channels. An 15V voltage supply should allow the electrical part to be turned on and run. This electrical component is included in the 6 series of products. A SPST - NO switching circuit is used to build these analog multiplexers. The multiplexer consists of 1 circuits. Try searching with MAX4520 if you're looking for variants. Internally, this switch multiplexer has a resistance of 390Ohm. To find out what the functions of 6 pins are, please refer to their datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. A voltage higher than 36V should not normally be supplied to the switches. Analog switch ics with Dual, Single supply type are cost-effective. It is recommended that the electrical component receives a voltage of 9V. It would be sufficient to run this analogue multiplexer with 50μA current. Put voltage above 175μA on the multiplexer to cause damage. Despite this switch's dual supply capability, its voltage should not exceed 20V. It is recommended that you attach at least 4.5V to your dual power supply. 20V operating voltages are supported by the electronic component. It conducts in a 4-bit manner.