MAX4521CEE+T

80ns, 30ns SPST - NC 100Ohm Analog Switches BREAK-BEFORE-MAKE MAX4521 16 Pins 1nA 5V 16-SSOP (0.154, 3.90mm Width)

Manufacturer: Maxim Integrated
Nocochips NO: 503-MAX4521CEE+T
Package: 16-SSOP (0.154, 3.90mm Width)
Datasheet: PDF
Stock: 707
Description: 80ns, 30ns SPST - NC 100Ohm Analog Switches BREAK-BEFORE-MAKE MAX4521 16 Pins 1nA 5V 16-SSOP (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-SSOP (0.154, 3.90mm Width)
Number of Pins	16
Operating Temperature	0°C~70°C TA
Packaging	Tape & Reel (TR)
Published	2007
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
ECCN Code	EAR99
Resistance	100Ohm
Terminal Finish	Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	696mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	5V
Terminal Pitch	0.635mm
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	MAX4521
Output	SEPARATE OUTPUT
Pin Count	16
Operating Supply Voltage	6V
Power Supplies	3/5/+-5V
Number of Channels	1
Number of Circuits	4
Max Supply Voltage	12V
Min Supply Voltage	2V
Operating Supply Current	1μA
Nominal Supply Current	1μA
Max Supply Current	1μA
Throw Configuration	SPST
Turn On Delay Time	80 ns
Voltage - Supply, Single/Dual (±)	2V~12V ±2V~6V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-5V
Turn-Off Delay Time	250 ns
Max Dual Supply Voltage	6V
On-State Resistance (Max)	100Ohm
Min Dual Supply Voltage	2V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	90 dB
Current - Leakage (IS(off)) (Max)	1nA
Channel Capacitance (CS(off), CD(off))	2pF 2pF
On-state Resistance Match-Nom	4Ohm
Switch Circuit	SPST - NC
Switch Time (Ton, Toff) (Max)	80ns, 30ns
Charge Injection	1pC
Channel-to-Channel Matching (ΔRon)	1 Ω
Crosstalk	-90dB @ 100kHz
Switching	BREAK-BEFORE-MAKE
Switch-off Time-Max	30ns
Normal Position	NC
Height Seated (Max)	1.73mm
Width	3.9mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant

MAX4521CEE+T Overview

The electronic part can be shipped overseas conveniently because it is packaged in 16-SSOP (0.154, 3.90mm Width). High reliability is achieved by using advanced packaging method Tape & Reel (TR). It is mounted in the position Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. Extended operating temperature around 0°C~70°C TA. In total, 16 terminations have occurred. This electronic part offers high-quality output due to its 1 channels. With a 5V voltage supply, the electrical component should be turned on and run. As part of the design of the 16 series, this electronic part has been incorporated into the system. A SPST - NC switching circuit is used for these analog switches. 4 circuits are used in this analogue multiplexer. Try searching for MAX4521 variants of the analog switch ic. In this multiplexer, the internal resistance is 100Ohm. For details about the functions of 16 pins, please refer to the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. A voltage higher than 12V should not normally be supplied to the switches. An effective Dual, Single supply digital multiplexer. The lowest voltage fed to the electronic component should be 2V. In order to operate this switch device, it would need a current of 1μA. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 6V. If you are using dual power supplies, you should attach at least 2V. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. This electrical part is compatible with 6V operating voltages.