MAX4521CUE+T
| Parameters | |
|---|---|
| On-state Resistance Match-Nom | 4Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 80ns, 30ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -90dB @ 100kHz |
| Switch-off Time-Max | 30ns |
| Height Seated (Max) | 1.1mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Terminal Finish | MATTE TIN |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX4521 |
| Pin Count | 16 |
| Operating Supply Voltage | 6V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 80 ns |
| Voltage - Supply, Single/Dual (±) | 2V~12V ±2V~6V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 2V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 2pF 2pF |
MAX4521CUE+T Overview
Shipping overseas is convenient with the electronic component packed in 16-TSSOP (0.173, 4.40mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. 1:1 is the ratio between multiplexers and demultiplexers. Operation at a temperature around 0°C~70°C TA. There are 16 terminations totally. As a result of its 1 channels, this electronic component provides high-quality output. Powered by a 5V voltage supply, the electrical part should be switched on and run. Into the electrical component body are injected 16 pins. Circuits based on SPST - NC switching are used to construct these analog switch ics. The circuits in this analogue multiplexer number 4. Try searching for the analog switch ic with MAX4521 if you are looking for variants. A 100Ohm internal resistance characterizes this multiplexer. To find out what the functions of 16 pins are, please refer to their datasheets. It is generally not recommended to supply a voltage higher than 12V to the switch device in normal circumstances. Dual, Single supply type digital switch with a low cost. A low voltage of 2V should be applied to the electronic component. An operating current of 1μA would be sufficient for this switch device. A digital multiplexer may suffer damage if voltage is applied above 1μA. If put voltage greater than 6V on the multiplexer, damage may be caused to the device. When using dual power supplies, you should attach at least 2V. 6V operating voltages can be used with this electrical part.
MAX4521CUE+T Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
MAX4521CUE+T Applications
There are a lot of Maxim Integrated MAX4521CUE+T Analog Switches & Multiplexers ICs applications.
- Low-Voltage
- Avionics and Military Systems
- Microwave transmission systems
- Medical systems
- Remote wireless modules
- Data Acquisition Systems
- MP3 players
- Data switching
- SONET/SDH ADM
- Audio/video switches
