MAX4522CEE+T

80ns, 30ns SPST - NO 100Ohm Analog Switches BREAK-BEFORE-MAKE MAX4522 16 Pins 1nA 5V 16-SSOP (0.154, 3.90mm Width)

Manufacturer: Maxim Integrated
Nocochips NO: 503-MAX4522CEE+T
Package: 16-SSOP (0.154, 3.90mm Width)
Datasheet: PDF
Stock: 622
Description: 80ns, 30ns SPST - NO 100Ohm Analog Switches BREAK-BEFORE-MAKE MAX4522 16 Pins 1nA 5V 16-SSOP (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Height Seated (Max)	1.75mm
Width	3.9mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-SSOP (0.154, 3.90mm Width)
Number of Pins	16
Operating Temperature	0°C~70°C TA
Packaging	Tape & Reel (TR)
Published	2007
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
ECCN Code	EAR99
Resistance	100Ohm
Terminal Finish	Tin (Sn)
Additional Feature	ALSO OPERATE WITH 2V TO 12V SINGLE SUPPLY
Subcategory	Multiplexer or Switches
Max Power Dissipation	696mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	5V
Terminal Pitch	0.635mm
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	MAX4522
Output	SEPARATE OUTPUT
Pin Count	16
Operating Supply Voltage	5V
Number of Channels	1
Number of Circuits	4
Max Supply Voltage	12V
Min Supply Voltage	2V
Operating Supply Current	1μA
Nominal Supply Current	1μA
Max Supply Current	1μA
Throw Configuration	SPST
Turn On Delay Time	100 ns
Voltage - Supply, Single/Dual (±)	2V~12V ±2V~6V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-5V
Turn-Off Delay Time	40 ns
Max Dual Supply Voltage	6V
On-State Resistance (Max)	100Ohm
Min Dual Supply Voltage	2V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	90 dB
Current - Leakage (IS(off)) (Max)	1nA
Channel Capacitance (CS(off), CD(off))	2pF 2pF
On-state Resistance Match-Nom	1Ohm
Switch Circuit	SPST - NO
Switch Time (Ton, Toff) (Max)	80ns, 30ns
Charge Injection	1pC
Channel-to-Channel Matching (ΔRon)	1 Ω
Crosstalk	-90dB @ 100kHz
Switching	BREAK-BEFORE-MAKE
Switch-on Time-Max	80ns
Switch-off Time-Max	30ns
Normal Position	NO

MAX4522CEE+T Overview

Shipping overseas is convenient with the electronic component packed in 16-SSOP (0.154, 3.90mm Width). Advanced packaging method Tape & Reel (TR) is used to provide high reliability. The multiplexer is located in Surface Mount. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operating temperature extended to 0°C~70°C TA. 16 terminations have been made so far. A electrical component with 1 channels is capable of high-quality output. An 5V voltage supply should allow the electrical part to be turned on and run. As part of the design of the 16 series, this electronic part has been incorporated into the system. Multiplexers built on a SPST - NO switching circuit are built. There are 4 circuits in this switch device. Try searching with MAX4522 if you're looking for variants. Internally, this switch multiplexer has a resistance of 100Ohm. You can find the functions of the 16 pins in the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. A voltage higher than 12V should not normally be supplied to the switches. Analog switch ics with Dual, Single supply type are cost-effective. 2V should be the lowest voltage fed to the electronic component. 1μA current would be enough for this multiplexer to operate. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. For this multiplexer, dual supply voltage is feasible, but it should not exceed 6V. With dual power supplies, you should attach at least 2V. This analog switch ic utilizes SEPARATE OUTPUT output. There is a voltage range of 5V operating voltages for the electrical part. This electronic part has additional features, such as: ALSO OPERATE WITH 2V TO 12V SINGLE SUPPLY.