MAX4522CPE
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Terminal Finish | TIN LEAD |
| Additional Feature | ALSO OPERATE WITH 2V TO 12V SINGLE SUPPLY |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Pin Count | 16 |
| JESD-30 Code | R-PDIP-T16 |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Voltage - Supply, Single/Dual (±) | 2V~12V ±2V~6V |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| On-State Resistance (Max) | 100Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 2pF 2pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 80ns, 30ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -90dB @ 100kHz |
| Switch-on Time-Max | 80ns |
| Switch-off Time-Max | 30ns |
| Length | 19.175mm |
| Width | 7.62mm |
| RoHS Status | Non-RoHS Compliant |
MAX4522CPE Overview
The electronic component is convenient to ship overseas because it is packed in a 16-DIP (0.300, 7.62mm). The advanced packaging method Tube provides high reliability. In Through Hole, you'll find this switch device. There is 1:1 ratio between the number of multiplexers and demultiplexers. Around 0°C~70°C TA is the extended operating temperature. Total terminations are 16. A 1 channel electronic part produces high-quality output. An 5V voltage supply should allow the electrical part to be turned on and run. It is part of the design of the 16 series that this electronic component is included. The analog switch ics are built using SPST - NO switching circuits. The multiplexer consists of 4 circuits. You shouldn't miss the additional features of the electrical component, such as: ALSO OPERATE WITH 2V TO 12V SINGLE SUPPLY.
MAX4522CPE Features
1 Channels
Switch Circuit: SPST - NO
Additional Features: ALSO OPERATE WITH 2V TO 12V SINGLE SUPPLY
MAX4522CPE Applications
There are a lot of Rochester Electronics, LLC MAX4522CPE Analog Switches & Multiplexers ICs applications.
- PDAs
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- DSLAMs
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Battery Powered Instruments
- Multi-Line E1 Interface Cards
- Switching Systems
- Transmit
- Audio and video signal routing
- Microprocessor controlled systems
